ATC and Online Flying

How to Connect MSFS to VATSIM with vPilot

Step-by-step guide to connecting Microsoft Flight Simulator to VATSIM with vPilot: install, configure audio and model matching, set up MSFS and connect.

On this page
  1. What you need before you start
  2. Step 1: Install vPilot
  3. Step 2: Configure vPilot
  4. Step 3: Prepare MSFS
  5. Step 4: File your flight plan
  6. Step 5: Connect
  7. Step 6: Tune and listen
  8. Useful vPilot commands
  9. Troubleshooting

What you need before you start

  • A VATSIM account with the new member orientation completed. Joining costs nothing; see is VATSIM free.
  • Microsoft Flight Simulator on a Windows PC. vPilot connects through the simulator’s SimConnect interface. Console editions cannot connect to VATSIM.
  • A headset or microphone, and a key or joystick button to use for push-to-talk.
  • A planned flight, ideally a short one from a quieter airport for your first time.

There is no built-in VATSIM mode in MSFS. vPilot is a separate free program that runs alongside the simulator, sends your position to the network, shows you other VATSIM pilots, and handles voice communication with controllers.

Step 1: Install vPilot

Download vPilot from its official website, linked from VATSIM’s pilot software page, and run the installer. Avoid copies from third-party download sites. vPilot supports Microsoft Flight Simulator as well as older Microsoft-based simulators such as Prepar3D and FSX.

Step 2: Configure vPilot

Open vPilot and go to its settings.

Network. Enter your VATSIM ID (the numeric CID), your password, your name as you want it shown, and optionally your home airport. You can leave the server choice on its default; VATSIM servers are linked to each other.

Audio. Choose your microphone and your headset or speakers. Set a push-to-talk key or joystick button, and use the microphone test to check your level. A quiet, clear signal with no background noise is the goal. Use push-to-talk rather than leaving the mic open.

Model matching. vPilot shows other VATSIM pilots by using aircraft models installed on your PC. Without a good set of models, other aircraft may appear as the wrong type or a generic aircraft. A widely used free option for MSFS is the FSLTL model set; install it and follow its instructions for linking it to vPilot. Model matching affects only what you see; it does not change anything for others.

Step 3: Prepare MSFS

Before connecting, change a few simulator settings so the sim does not clash with the network:

  • Turn off AI traffic and the simulator’s live or multiplayer traffic. vPilot injects real VATSIM pilots. Leaving other traffic on means you will see aircraft that do not exist on the network and may queue behind them or report them to controllers.
  • Silence the built-in ATC. Turn the ATC volume down or disable it so the AI does not give instructions that contradict the human controller.
  • Load at a parking spot. Start at a gate, stand or ramp. Never connect on a runway, taxiway or in the air, as you may appear in front of someone else’s landing.
  • Use real-time settings. Do not use simulation rate acceleration on the network, and avoid pausing while under ATC control.

Step 4: File your flight plan

File your flight plan on myVATSIM (or prefile from SimBrief) using the callsign you are about to connect with. Our guide on how to file a VATSIM flight plan explains each field. If this is your first flight, a remark such as NEW TO VATSIM helps controllers help you.

Step 5: Connect

With MSFS loaded at your parking spot, click Connect in vPilot and fill in:

  • Callsign: must match your flight plan.
  • Type code: the ICAO aircraft type, e.g. A20N, B738, C172.
  • SELCAL: optional; leave blank if you do not know it.
  • Observer mode: tick this only if you want to listen without flying.

Once connected, vPilot shows a confirmation message and you should see other VATSIM aircraft around you. The network’s online maps update with a short delay, so do not worry if you do not appear instantly.

Listening first. If you are nervous, connecting as an observer, or sitting at a gate and just listening for a while, is a perfectly acceptable way to learn how a frequency sounds.

Step 6: Tune and listen

vPilot lists nearby controllers with their frequencies. Before calling:

  1. Tune and listen to the ATIS if one is online, and note the information letter, runway in use and altimeter setting.
  2. Tune the lowest staffed position that covers your airport. Coverage works top-down: if there is no delivery or ground controller, tower may cover those duties; if there is no tower, an approach or centre controller above may provide service.
  3. Listen for a moment so you do not talk over someone, then make your call.

If no controller covers your airport, use UNICOM on 122.800 and announce your intentions, commonly by text. Our guide to VATSIM radio phraseology for beginners has example calls for each stage.

Set your transponder correctly too. Controllers see your squawk code and whether you are in standby or an active mode, so follow the client’s transponder controls or your aircraft’s panel, depending on how your aircraft and vPilot are set up.

Useful vPilot commands

vPilot accepts “dot commands” typed into its message box. Some common ones:

Command What it does
.x 1234 Sets your transponder code to 1234
.com1 121.800 Tunes COM 1 to the given frequency
.chat CALLSIGN Opens a private text chat with another user

vPilot’s documentation lists the full set. Commands can change between versions, so check the docs if one does not work.

Troubleshooting

  • vPilot does not detect the simulator. Make sure MSFS is fully loaded into a flight, then try reconnecting. Running vPilot and MSFS at the same permission level (both normal, or both as administrator) can help.
  • You cannot hear controllers. Confirm the frequency is tuned as active on COM 1 and that the receive volume is up, then check vPilot’s output device.
  • Controllers cannot hear you. Check the push-to-talk binding and microphone device, and watch for vPilot’s transmit indicator.
  • Other aircraft show as the wrong type. Install or reconfigure your model matching set.
  • Ghost aircraft blocking taxiways. You probably left AI or multiplayer traffic on.
  • Controller says they cannot see your flight plan. Check the callsign matches exactly, then refresh the plan.

Once you are comfortable, you may want structured training; see VATSIM pilot ratings explained. For how VATSIM compares with the default ATC and AI add-ons, see our overview of ATC in Microsoft Flight Simulator.

The complete guide to atc and online flying

ATC in Microsoft Flight Simulator: Default AI vs Real Controllers
Read the guide

Keep exploring

Guides from other topics

All topics →