To contact ATC in Microsoft Flight Simulator, make sure your aircraft’s COM radio is powered and tuned (or set to auto-tune), then open the ATC window and choose a numbered message. On PC, the ATC window opens from the toolbar at the top of the screen, and in MSFS 2020 the default keyboard shortcut is Scroll Lock. On console, open the toolbar in cursor mode and select the ATC panel. Your pilot reads the message aloud and the controller replies.
Step 1: Make sure your radio is on
The built-in ATC is tied to your aircraft’s radios. If you start “cold and dark”, nothing will work until the radios have power.
- Turn on the battery and, if needed, the avionics master or external power.
- On airliners such as the A320, make sure the radio panel is on and the receive volume for the relevant VHF radio (usually VHF 1 / COM 1) is turned up and selected.
- Check the simulator’s audio settings so the ATC and radio volume are not muted.
If you start on the runway or at a gate with engines running, the radios are normally already on.
Step 2: Open the ATC window
PC
- Click the ATC icon on the toolbar at the top of the screen (move the mouse to the top edge if the toolbar is hidden).
- Or press Scroll Lock, the default shortcut in MSFS 2020. If it does nothing, check the Controls options for the “toggle ATC” binding, since bindings can differ by version and can be changed.
You can move and resize the ATC window so it stays visible while you fly.
Xbox and other consoles
Enter cursor mode with your controller, open the toolbar at the top of the screen and select the ATC panel. The exact button combination depends on the console, controller profile and simulator version, so check the controls menu if your usual shortcut does not work. You can also bind the ATC panel to a button of your choice.
Step 3: Tune the right frequency (or use auto-tune)
Each ATC station has its own frequency. You can tune it yourself using the radio in the cockpit, or let the simulator do it:
- Auto-tune. The ATC window can tune the frequency for you when you choose a message for a new station. This is the easiest way to start.
- Manual tuning. Set the frequency in your standby COM window and swap it to active. Frequencies for nearby stations are listed in the ATC window and on the world map airport information.
Keyboard shortcuts for radios can be useful on PC, but defaults change between versions, so check the controls menu rather than relying on a memorised list.
Step 4: Choose your message
The ATC window shows a numbered list of messages you can transmit. Pick a number on the keyboard or click the message. Your virtual pilot reads it, ATC replies, and the list updates with the next logical options. A simple rule from experienced users: if you are unsure what to do next, the first option on the list is usually the expected next step.
When ATC gives you an instruction, you will typically see an option to acknowledge or read it back. Do this before flying on, or ATC may repeat itself.
A typical flight, call by call
This is the general order for an IFR flight with the default ATC, following the phases of flight. VFR flights skip the clearance and usually involve fewer handoffs.
- Clearance. Request your IFR clearance from clearance delivery or ground. Read it back.
- Taxi. Request taxi from ground. Follow the taxi line or route shown and hold short where told.
- Takeoff. Switch to tower and report ready. Wait for takeoff clearance before rolling.
- Departure. After takeoff, tower hands you to departure. Check in and follow headings and altitudes.
- En route. Centre controllers manage your climb, cruise and descent. Accept handoffs as they come.
- Arrival. Approach gives you descent, vectors and an approach clearance.
- Landing. Tower clears you to land.
- Taxi in. After vacating the runway, contact ground for taxi to parking.
Troubleshooting
- “There are currently no messages to transmit.” You may be out of range of any station, on the wrong frequency, or at a point in the flight where nothing needs saying. Try tuning a different station or opening the list of nearby frequencies.
- No audio from ATC. Check aircraft power, the radio’s receive volume and the simulator’s ATC volume.
- ATC keeps repeating an instruction. You probably did not acknowledge it. Select the readback option.
- Messages for the wrong airport. Auto-tune can pick a nearby station. Tune the correct frequency manually.
- Conflicting instructions while flying online. If you connect to VATSIM or IVAO, turn off or mute the default ATC so the AI does not talk over real controllers.
Can you actually talk to ATC with your voice?
Not with the default system; it is menu-driven only, and its controllers are software rather than people (see is ATC in Microsoft Flight Simulator real people?). To use your voice you have two routes:
- AI ATC add-ons with speech recognition, such as BeyondATC, SayIntentions.AI or Pilot2ATC. Compare them in AI ATC add-ons for MSFS.
- Online networks with human controllers, such as VATSIM. Start with how to connect MSFS to VATSIM with vPilot and learn the calls in VATSIM radio phraseology for beginners.
Our overview of ATC in Microsoft Flight Simulator compares all of these in one place.