Learn to Fly

ILS Approach Training in Microsoft Flight Simulator

Learn to fly an ILS approach in Microsoft Flight Simulator: how the localizer and glideslope work, avionics setup, hand-flying, autopilot, and troubleshooting.

On this page
  1. How an ILS Works
  2. Reading the Approach Chart
  3. Setting Up a Practice Session in MSFS
  4. Configuring the Avionics
  5. Flying the Approach by Hand
  6. Flying the Approach on Autopilot
  7. The Missed Approach
  8. Troubleshooting: Why Isn’t My ILS Working?
  9. A Training Progression

The instrument landing system (ILS) is the classic precision approach. It guides you laterally and vertically down to a runway in poor visibility. It’s also one of the most satisfying things to master in Microsoft Flight Simulator, and one of the most common sources of frustration: missed glideslopes, needles that never move, and an autopilot that flies straight through the localizer. This guide explains how the ILS works, how to set it up in both a round-dial Cessna and a G1000, and how to fix the usual problems.

How an ILS Works

An ILS has two main radio beams:

  • Localizer: lateral guidance aligned with the runway centerline. It’s much more sensitive than a VOR. Full-scale needle deflection is only a few degrees either side of the centerline, so small heading changes have a big effect close in.
  • Glideslope: vertical guidance, typically set at about 3 degrees, ending near the touchdown zone.

You fly the approach by keeping both needles centered (or the diamond and course needle on a glass display) until you reach the decision altitude, shown on the chart as DA. For a typical Category I ILS this is about 200 feet above the touchdown zone. If you can see the runway environment there, you land. If not, you fly the missed approach.

A handy rule of thumb: on a 3-degree glideslope, your descent rate in feet per minute is roughly groundspeed in knots × 5. At 90 knots groundspeed that’s about 450 fpm; at 140 knots, about 700 fpm.

Reading the Approach Chart

Before flying, find these items on the ILS chart for your runway:

  • Localizer frequency and identifier (for example, 110.3, I-ABC)
  • Final approach course, the inbound magnetic course
  • Glideslope intercept altitude, usually marked with a lightning-bolt symbol at the final approach fix
  • Decision altitude for your aircraft’s approach category
  • Missed approach procedure: climb instructions and the holding fix

Charts for real-world airports are available from several free and subscription sources, and MSFS’s own navigation data generally matches them closely.

Setting Up a Practice Session in MSFS

  1. Pick a medium-sized airport with a published ILS and a long runway.
  2. Use clear weather and calm wind for the first few attempts, then add low clouds later.
  3. Start airborne about 10 to 15 nautical miles out, roughly aligned with the runway, at or above the glideslope intercept altitude. You can position yourself with the world map, a saved flight, or by flying there and saving.
  4. Choose a trainer you know, such as a Cessna 172, before moving to faster aircraft.

Configuring the Avionics

Steam-gauge Cessna 172

  1. Tune the localizer frequency into the active NAV1 frequency, not just standby.
  2. Identify the station by listening to its Morse code ident on the audio panel, as real pilots do.
  3. Set the OBS (or HSI course pointer) to the final approach course. On a basic CDI the OBS doesn’t change localizer sensing, but setting it gives you a visual reference.
  4. Confirm the glideslope needle appears and its warning flag disappears as you get closer.

Garmin G1000

  1. Load the ILS through the PROC button on the MFD, choosing a transition or vectors-to-final.
  2. Check that the localizer frequency is in the active NAV1 slot. The G1000 usually loads it for you, but verify.
  3. Watch the CDI source. It should change from GPS to LOC1 as you approach the final course. If it doesn’t, press the CDI softkey until it shows LOC1.
  4. Confirm the glideslope diamond appears beside the altitude tape.

For a fuller tour of these steps, see Garmin G1000 basics in Microsoft Flight Simulator.

Flying the Approach by Hand

Intercepting the localizer

  • Fly a heading that crosses the final approach course at about 30 degrees or less.
  • When the localizer needle comes off the side of the instrument and starts moving, begin your turn onto the inbound course. Lead the turn slightly, because the localizer is sensitive.
  • Once established, make small heading corrections of 2 to 5 degrees and hold them for a few seconds before judging the result.

Capturing the glideslope

  • Stay level at the intercept altitude so you meet the glideslope from below.
  • As the glideslope needle centers, reduce power and lower the nose to your target descent rate. Extend gear and flaps per your aircraft’s procedure.
  • Fix glideslope errors with small pitch changes and fix speed with power, adjusting both together.
  • Keep the airplane trimmed. A well-trimmed airplane makes the approach far more stable; see how to use elevator trim.

To minimums and landing

  • Scan the localizer, glideslope, airspeed, and altimeter continuously.
  • Call out “minimums” at the decision altitude.
  • With the runway in sight, transition to visual flying and land. Our guide to landing smoothly in Microsoft Flight Simulator covers the flare.

Flying the Approach on Autopilot

  1. Fly heading mode (HDG) toward the localizer intercept.
  2. Set the altitude preselect to the glideslope intercept altitude and hold it with ALT.
  3. Press APR to arm approach mode before reaching the localizer. The localizer and glideslope show as armed, then captured, on the mode annunciator.
  4. Monitor that both capture. If the glideslope doesn’t capture, you may be above it. Never descend to meet a glideslope from above in normal training.
  5. Disconnect the autopilot no later than the decision altitude and land by hand. In airliners the process differs; see our A320 tutorial for MSFS and the explainer on what a flight director is.

The Missed Approach

If you reach decision altitude without the runway in sight:

  1. Apply full power and pitch for a climb.
  2. Clean up flaps in stages, and gear if retractable, once climbing.
  3. Fly the published missed approach procedure: usually a climb on a heading or course to a fix, then a hold.
  4. Re-brief and try again.

Practise missed approaches on purpose. They’re high-workload, and the sim is the perfect place to rehearse them.

Troubleshooting: Why Isn’t My ILS Working?

Symptom Likely cause Fix
No localizer or glideslope indication Frequency in standby, not active Swap the frequency into active NAV1
G1000 needle follows GPS, not the ILS CDI source still on GPS Press the CDI softkey to LOC1
Autopilot flies through the localizer APR not armed, or intercept angle too steep Arm APR earlier; intercept at 30° or less
Glideslope never captures Approaching from above, or APR pressed too late Level at intercept altitude below the glideslope
Needles flicker or point oddly Too far out or below reception range Get closer or higher; check the ident
ATC gives a runway with a tailwind Default ATC runway selection Request a different runway or self-position
Approach not in the flight plan Approach loaded but not activated, or not loaded Load and activate via PROC, or use vectors-to-final

A Training Progression

  1. Straight-in finals: start 8 to 10 miles out, already aligned. Focus only on keeping the needles centered.
  2. Intercepts: start off to one side and practise heading onto the localizer.
  3. Full procedures: fly from an initial approach fix, including any procedure turn or hold.
  4. Weather: add low ceilings, then wind, then turbulence.
  5. Partial panel: fail an instrument and fly it again. See the six pack of flight instruments for which failures to try.

Before tackling ILS work, make sure you’re comfortable with VOR navigation and tracking radials, because the needle-reading skills carry over directly.

The complete guide to learn to fly

Learning to Fly with a Flight Simulator
Read the guide

Keep exploring

Guides from other topics

All topics →