Learn to Fly

Flying a Traffic Pattern in a Flight Simulator

How to fly a traffic pattern in your flight sim: the five legs, pattern altitude, 45-degree entries, power and flap cues, wind correction, and radio calls.

On this page
  1. What Is a Traffic Pattern?
  2. The Legs of the Pattern
  3. Pattern Altitude and Direction
  4. Entering the Pattern
  5. Flying One Lap: Step by Step (Cessna 172 Example)
  6. Wind Correction on Each Leg
  7. The Base-to-Final Turn
  8. Radio Calls at a Non-Towered Airport
  9. Practising Patterns in a Simulator

The traffic pattern is the standard rectangular circuit flown around a runway for takeoffs and landings. It keeps arrivals and departures predictable and gives you a consistent setup for every landing. Flying it well is the foundation of good landings, so it’s one of the most valuable things to practise in a flight simulator.

What Is a Traffic Pattern?

Instead of flying straight at the runway, pilots join a rectangular path at a set altitude and direction. Everyone flying the same pattern knows where to look for other traffic, and every landing starts from a similar position, altitude, and speed. The FAA’s Airplane Flying Handbook and Aeronautical Information Manual describe the standard pattern used at most US airports. Other countries use similar circuits with some local differences.

The Legs of the Pattern

  1. Departure (upwind) leg: climbing straight out along the runway heading after takeoff.
  2. Crosswind leg: a 90-degree turn after takeoff, flown perpendicular to the runway.
  3. Downwind leg: flown parallel to the runway in the opposite direction to landing, typically about ½ to 1 mile out for a light aircraft.
  4. Base leg: a 90-degree turn toward the runway after passing the landing point.
  5. Final approach: aligned with the runway centerline, descending to land.

“Upwind” can also refer to flying parallel to the runway on the landing direction side, for example after a go-around.

Pattern Altitude and Direction

  • Altitude: a common pattern altitude for propeller aircraft is 1,000 feet above ground level (AGL). Some airports publish different altitudes, so check the airport information in your sim or a chart supplement for real airports. Remember to add the field elevation to get the altitude you’ll fly on the altimeter.
  • Direction: the standard pattern uses left turns. Some runways specify right traffic, usually to avoid terrain, noise-sensitive areas, or another airport.

Entering the Pattern

  • Standard entry: join the downwind leg at a 45-degree angle, aiming for the midpoint of the runway, at pattern altitude.
  • From the opposite side: one common method is to cross over the airport above pattern altitude, typically 500 to 1,000 feet above it, continue well clear, descend, and turn back to join on the 45.
  • Towered airports: follow ATC’s instructions, which can include straight-in or base entries.
  • Before joining, check the wind and active runway (ATIS or AWOS where available), listen to the frequency, and look for traffic.

Flying One Lap: Step by Step (Cessna 172 Example)

These are typical numbers many instructors use for a Cessna 172. Your aircraft’s handbook and your instructor’s procedures take priority.

Takeoff and climb

  1. Take off and climb at the recommended climb speed, staying aligned with the runway.
  2. Beyond the departure end, and within about 300 feet of pattern altitude, turn onto crosswind.

Crosswind 3. Continue the climb to pattern altitude. 4. Turn downwind at a point that gives the correct spacing from the runway.

Downwind 5. Level off at pattern altitude and reduce power to a comfortable pattern speed. 6. Complete the before-landing checklist: fuel, mixture, carburettor heat if applicable, and seatbelts. 7. Abeam the landing point (often called “abeam the numbers”), reduce power, hold altitude as the airplane slows, then add the first stage of flaps within the white arc. Begin a gentle descent.

Base 8. When the landing point is about 45 degrees behind your wing, turn base. 9. Add more flaps, continue descending, and slow toward approach speed. 10. Look along final for traffic and start your turn so you roll out on the centerline.

Final 11. Set landing flaps, fly your target approach speed, and use an aim point; see how to land smoothly in Microsoft Flight Simulator. 12. Land, or for a touch-and-go: flaps up, carburettor heat off, full power, and take off again.

Targets to grade yourself on: altitude ±100 feet on downwind, approach speed within about 5 knots on final, and rollout on the centerline without overshooting.

Wind Correction on Each Leg

Wind pushes the pattern out of shape, so correct for it on each leg:

  • Crosswind leg: crab into the wind so your track stays perpendicular to the runway.
  • Downwind: crab to stay at a constant distance from the runway. With a tailwind on downwind your groundspeed is higher, so things happen sooner.
  • Base: a headwind on final means a tailwind component on base. Turn earlier, and expect a slower groundspeed on final.
  • Final: hold the centerline using the crab or wing-low method; see crosswind landings in a flight sim.

The Base-to-Final Turn

The turn onto final deserves care. Overshooting the centerline, then tightening the turn with too much rudder, creates a skidding, cross-controlled turn at low speed and low altitude. That’s a classic setup for a stall. Keep bank moderate and coordinated, with the ball centered. If you overshoot, accept it and correct gently, or go around. Practising slow flight and stalls shows you why.

Radio Calls at a Non-Towered Airport

At airports without a tower, pilots announce their position on the common traffic advisory frequency (CTAF). A typical sequence:

  • “[Airport] traffic, Cessna 123AB, 10 miles south, inbound for landing, runway 27, [airport].”
  • “[Airport] traffic, Cessna 123AB, entering left downwind, runway 27, [airport].”
  • “[Airport] traffic, Cessna 123AB, left base, runway 27, [airport].”
  • “[Airport] traffic, Cessna 123AB, final, runway 27, [airport].”
  • “[Airport] traffic, Cessna 123AB, clear of runway 27, [airport].”

Saying the airport name at the start and the end helps others who share the frequency. For more on radio technique, see VATSIM radio phraseology for beginners.

Practising Patterns in a Simulator

  • Pick a quiet, simple airport with a single runway and clear surroundings.
  • Use a saved flight on the runway so you can restart quickly.
  • Fly 5 to 10 laps per session, each a touch-and-go or a full stop and taxi back.
  • Use visual references. Note landmarks marking your downwind distance and base turn so each lap matches.
  • Practise with ATC. The sim’s built-in ATC, or an online network such as VATSIM, lets you rehearse radio work.
  • Add wind once calm-wind patterns are consistent.

For where pattern work fits in the bigger picture, see our learning to fly with a flight simulator roadmap.

The complete guide to learn to fly

Learning to Fly with a Flight Simulator
Read the guide

Keep exploring

Guides from other topics

All topics →