Learn to Fly

Flight Levels vs Altitude: What FL180 and Above Means

The difference between altitude and flight levels, what FL180 means in the US, transition altitude vs level, lowest usable flight level, and how to handle it in a sim.

On this page
  1. The Short Answer
  2. What Is Altitude? The Types Pilots Use
  3. What Is a Flight Level?
  4. Transition Altitude and Transition Level
  5. What FL180 Means in the United States
  6. How High Is Flight Level 600?
  7. Cruising Levels and the Direction-of-Flight Rule
  8. Common Questions
  9. Handling the Changeover in Your Simulator

The Short Answer

An altitude is read with the altimeter set to the local barometric pressure, so it approximates height above mean sea level. A flight level is read with the altimeter set to a fixed standard pressure of 29.92 inches of mercury (1013.25 hPa), and it’s written in hundreds of feet. FL180 means 18,000 feet of pressure altitude.

Pilots switch from altitudes to flight levels when they climb through the transition altitude. In the United States and Canada that’s 18,000 feet. Above it, every aircraft uses the same altimeter setting, so vertical separation stays consistent even as the weather changes along the route.

What Is Altitude? The Types Pilots Use

“Altitude” sounds simple, but pilots use several kinds:

  • Indicated altitude: what the altimeter shows with the current local setting dialled in.
  • True altitude: actual height above mean sea level (MSL). Charts show terrain and obstacles in MSL.
  • Absolute altitude: height above the ground directly below (AGL).
  • Pressure altitude: the altimeter reading when set to 29.92 inHg, meaning height above the standard datum plane.
  • Density altitude: pressure altitude corrected for non-standard temperature. It describes how the airplane performs, not where it is.

Below the transition altitude, pilots fly indicated altitudes based on local pressure (QNH), because that keeps them reasonably accurate relative to terrain. Above it, they fly flight levels.

What Is a Flight Level?

A flight level is a surface of constant atmospheric pressure, labelled by the altitude it would correspond to in the standard atmosphere. With 29.92 set:

Because everyone above the transition altitude uses the same setting, two aircraft at FL350 and FL360 stay 1,000 feet apart on their altimeters. That holds even if one of them is flying into a low-pressure system. Their true altitudes above sea level may both shift, but they shift together.

Transition Altitude and Transition Level

Two terms define the changeover:

  • Transition altitude: the altitude at or below which you use local pressure. Climbing through it, you set standard pressure.
  • Transition level: the lowest flight level available above the transition altitude. Descending through it, you set local pressure.

The gap between them is the transition layer. In the US and Canada the transition altitude is 18,000 feet everywhere, and FL180 normally serves as the transition level. In much of the rest of the world, transition altitudes are far lower. They vary by country and sometimes by airport, often only a few thousand feet, and the transition level may change with the day’s pressure. Always check the chart or ATIS for the airport you’re using.

What FL180 Means in the United States

The base of Class A airspace

In the US, Class A airspace starts at 18,000 feet MSL and extends up to and including FL600. All flights in Class A must operate under instrument flight rules (IFR) with an ATC clearance. So FL180 marks both the switch to standard pressure and the start of IFR-only airspace.

Lowest usable flight level

When local pressure is lower than standard, an altimeter set to 29.92 reads higher than the aircraft’s true altitude. An aircraft at “FL180” could then actually be below 18,000 feet MSL, too close to traffic flying altitudes just below. To protect that buffer, ATC raises the lowest flight level it will assign when the altimeter setting is low:

Local altimeter setting Lowest usable flight level
29.92 inHg or higher FL180
29.91 to 28.92 inHg FL190
28.91 to 27.92 inHg FL200

This follows the FAA’s published table. As a simmer, you’ll mostly notice it on online networks when a controller declines to assign FL180 on a low-pressure day.

How High Is Flight Level 600?

FL600 is a pressure altitude of 60,000 feet. In the US it’s the top of Class A airspace. Airspace above FL600 is Class E. Very few aircraft operate that high. Typical airliners cruise well below it, and only specialised high-altitude aircraft such as some military and research types regularly go there.

Cruising Levels and the Direction-of-Flight Rule

To reduce head-on conflicts, cruising levels depend on the direction of flight. Under US IFR rules in the flight-level structure:

  • Magnetic course 0° to 179° (roughly eastbound): odd thousands, such as FL190, FL230, and FL350
  • Magnetic course 180° to 359° (roughly westbound): even thousands, such as FL180, FL240, and FL360

Between FL290 and FL410, aircraft approved for reduced vertical separation minimums (RVSM) keep 1,000-foot spacing. Above FL410 the spacing widens to 2,000 feet. Other countries use similar but not always identical schemes, and ATC can assign other levels. A planning tool or online network will normally suggest a valid level.

Common Questions

What is the average altitude of a flight?

It depends on the aircraft and route length. Jet airliners on longer flights typically cruise somewhere around FL300 to FL400, roughly 30,000 to 40,000 feet. Short flights may never get that high. Turboprops usually cruise lower, and small piston trainers generally fly under about 10,000 feet.

Is 5,000 feet considered high altitude?

Not in aviation terms. A light aircraft at 5,000 feet is in ordinary low-level airspace, and supplemental oxygen isn’t required there. In the US, oxygen rules for pilots start above 12,500 feet MSL. Airports at around 5,000 feet elevation, such as Denver’s, do need attention to density altitude, though. On hot days, aircraft performance at high-elevation airports can drop noticeably.

How do you get pressure altitude below 18,000 feet?

The easiest way is to briefly set 29.92 in the altimeter and read the result, then reset the local setting. You can also calculate it: subtract the local altimeter setting from 29.92, multiply by 1,000, and add the field elevation or indicated altitude. Our pressure altitude guide walks through an example.

Handling the Changeover in Your Simulator

  • On the climb: passing the transition altitude, set standard pressure. In many glass and airliner cockpits this is a STD button or a push of the baro knob. In a classic Cessna you turn the knob to 29.92.
  • On the descent: at the transition level, set the destination’s local pressure from the ATIS or the sim’s weather. Many simulators, including MSFS, have a key binding to set the altimeter to the current local pressure. Check your control settings for it.
  • Use live weather. With real-world weather turned on, pressure varies by location, so forgetting the changeover produces realistic altitude errors.
  • Practise on a network. Flying on VATSIM or IVAO, controllers will expect correct flight levels and altimeter settings.
  • In an airliner, set the transition altitude in the flight management system so the PFD reminds you to switch. Our A320 tutorial for MSFS shows where this fits into the climb.

For more on the theory behind the number, read what is the definition of pressure altitude.

The complete guide to learn to fly

Learning to Fly with a Flight Simulator
Read the guide

Keep exploring

Guides from other topics

All topics →