Learn to Fly

VOR Navigation Explained: Tracking Radials in the Sim

Learn VOR navigation in your flight sim: radials, the OBS and CDI, TO/FROM flags, intercepting and tracking a radial with wind correction, and practice drills.

On this page
  1. What Is a VOR?
  2. Radials: The Key Idea
  3. The VOR Instrument: OBS, CDI, and TO/FROM Flag
  4. Tuning and Identifying a VOR in the Sim
  5. Finding Where You Are
  6. Intercepting a Radial
  7. Tracking a Radial with Wind Correction
  8. Flying To vs From a Station
  9. Avoiding Reverse Sensing
  10. VOR on a Glass Cockpit
  11. Practice Exercises

Before GPS, the VOR was the backbone of air navigation, and it’s still taught in pilot training and used as a backup. Learning to track VOR radials in a simulator builds the same needle-reading skills you’ll need for ILS approaches and instrument flying. This guide explains how VORs work, how to read the instrument, and how to intercept and track a radial with a crosswind.

What Is a VOR?

A VOR (VHF omnidirectional range) is a ground radio station that transmits signals your receiver uses to work out your magnetic bearing from the station. VORs operate in the VHF band between 108.00 and 117.95 MHz. Reception is line-of-sight, so the higher you fly, the farther away you can receive a station. Each VOR transmits a three-letter Morse code identifier so you can confirm you’ve tuned the right one.

Radials: The Key Idea

A radial is a magnetic bearing line going out from the station, like the spokes of a wheel. There are 360 of them:

  • the 090 radial runs due east (magnetic) from the station
  • the 270 radial runs due west from the station
  • an aircraft on the 180 radial is south of the station, whichever way it’s pointing

That last point is the one that confuses people. Radials tell you where you are, not where you’re heading. A VOR receiver doesn’t know your heading.

The VOR Instrument: OBS, CDI, and TO/FROM Flag

A basic VOR indicator has three parts:

  • OBS (omni bearing selector): the knob that rotates the course card to select a course.
  • CDI (course deviation indicator): the vertical needle. It shows whether the selected course is to your left or right. On a typical VOR display, full-scale deflection is about 10 degrees either side, so each dot on a five-dot scale is roughly 2 degrees.
  • TO/FROM flag: shows whether the selected course would take you to or from the station. An OFF or NAV flag means no usable signal.

Fly toward the needle. If the needle is to the right, the course is to your right.

Tuning and Identifying a VOR in the Sim

  1. Find the frequency on a sectional chart, an en-route chart, or the sim’s map.
  2. Tune it into the active NAV radio, usually NAV1.
  3. Turn on the NAV1 audio on the audio panel and listen for the Morse identifier. Compare it with the chart.
  4. Confirm the warning flag has cleared.

Skipping step 3 is how pilots end up tracking the wrong station.

Finding Where You Are

To find which radial you’re on:

  1. Turn the OBS until the needle centers with a FROM flag.
  2. The number at the top of the course card is the radial you’re on.

To find the course to the station, center the needle with a TO flag. With two VORs you can draw both radials on a chart, and you’re where they cross. This is a classic way to fix your position if you’re unsure, and it’s part of the lost-pilot routine in the 5 C’s of flight.

Intercepting a Radial

Say you want to fly outbound on the 060 radial.

  1. Set the OBS to 060. The flag should read FROM if you’re on that side of the station.
  2. See which way the needle points. Say it’s deflected to the left, so the course is to your left.
  3. Pick an intercept heading 30 to 45 degrees toward the course from 060. Here that’s about 030 or 015.
  4. Fly that heading and watch the needle move toward center.
  5. Lead the turn as the needle approaches center, so you roll out on 060 without overshooting. The closer you are to the station, the faster the needle moves and the earlier you’ll need to turn.

Steeper intercepts get you there faster but are easier to overshoot. Shallower intercepts are smoother.

Tracking a Radial with Wind Correction

Once on course, wind will push you off. The standard method is bracketing:

  1. Fly the course heading (060) and watch the needle.
  2. If the needle drifts left, the wind is pushing you right. Turn about 10 to 20 degrees left to re-intercept, for example to 045.
  3. As the needle re-centers, turn back toward the course, but keep part of the correction, for example a heading of 055.
  4. Watch again. If the needle stays centered, you’ve found your wind correction angle. If it drifts again, halve or double the correction and repeat.

The aim is to find a heading that keeps the needle centered. You’ll often need a few degrees of correction into the wind, and the amount changes with wind and airspeed.

Flying To vs From a Station

  • Inbound (TO): set the course you want to fly toward the station. For example, to fly in on the 240 radial, set 060 with a TO flag.
  • Station passage: as you pass over the station, the needle may swing and the flag flips from TO to FROM. There’s an area of confusion directly above the station, often described as a “cone,” where indications are unreliable. Hold your heading through it.
  • Outbound (FROM): after passage, set the outbound course and keep tracking.

Avoiding Reverse Sensing

On a basic CDI, if the selected course is roughly opposite your heading, the needle works backwards. “Fly toward the needle” then takes you farther off course. This happens when your OBS setting doesn’t match your direction of flight, for example a FROM flag while you’re heading toward the station.

The fix is simple: set the OBS to roughly match the direction you’re flying. If you’re heading toward the station, you should see a TO flag; heading away, a FROM flag.

An HSI (horizontal situation indicator) shows the course needle on a rotating compass card. Set correctly, it never reverse-senses, because the display turns with your heading. That’s one reason pilots like it.

VOR on a Glass Cockpit

In a G1000-equipped aircraft:

  • tune the VOR in NAV1 and identify it
  • press the CDI softkey until the HSI shows VOR1; the needle turns green
  • set the course with the CRS knob
  • the HSI then works like a traditional HSI

The most common sim mistake is leaving the CDI on GPS and wondering why the needle ignores the VOR. More on this in Garmin G1000 basics in Microsoft Flight Simulator.

Practice Exercises

Turn off the GPS and moving map for these, or use a steam-gauge aircraft:

  1. Where am I? Start somewhere random, tune a VOR, and find your radial. Repeat with a second VOR and plot your position.
  2. Fly to the station: center the needle with a TO flag and track inbound to station passage.
  3. Radial intercepts: from overhead a VOR, intercept and fly outbound on four different radials.
  4. Wind practice: set a 20-knot crosswind to your course and bracket to find the correction angle.
  5. VOR-to-VOR cross-country: plan a short flight using VORs as waypoints.

Once these feel easy, the more sensitive localizer awaits in ILS approach training in Microsoft Flight Simulator. Strong instrument scanning skills help too; see the six pack of flight instruments explained.

The complete guide to learn to fly

Learning to Fly with a Flight Simulator
Read the guide

Keep exploring

Guides from other topics

All topics →