Learn to Fly

How to Land Smoothly in Microsoft Flight Simulator

Land smoothly in Microsoft Flight Simulator with a stabilised approach, a good aim point, a patient flare, and sim settings that make depth and control feel right.

On this page
  1. Why Landings Feel Harder in a Sim
  2. Set Up Your Sim for Better Landings
  3. Start with a Stabilised Approach
  4. Use an Aim Point and the PAPI
  5. The Flare: Where Smooth Landings Happen
  6. After Touchdown
  7. Fixing Common Problems
  8. Landing Airliners Smoothly
  9. A Practice Routine

Smooth landings in Microsoft Flight Simulator come from the same things that produce smooth landings in a real airplane: a stable approach, a consistent aim point, and a patient flare. But the sim adds its own challenges, such as a flat screen, spring-loaded controls, and default settings that hide what’s happening. This guide covers both sides, using a light trainer such as the Cessna 172 as the example.

Why Landings Feel Harder in a Sim

  • Weak depth cues. On a monitor it’s hard to judge height in the last few feet, which is exactly where the flare happens.
  • Narrow field of view. A zoomed-in view makes everything feel slower and closer, so you flare late.
  • Control sensitivity. Short-throw joysticks and default curves can make small pitch changes large.
  • No seat-of-the-pants cues. You can’t feel the airplane sinking.
  • Assists. Options such as assisted landing or auto-rudder can fight your inputs.

Fixing the setup removes much of the frustration before you change your technique.

Set Up Your Sim for Better Landings

  1. Field of view: zoom out to a natural view where you can see the panel’s top instruments and a good stretch of runway ahead. Many simmers keep this view consistent from flight to flight.
  2. Head tracking or VR: looking toward the far end of the runway in the flare is much easier with either.
  3. Control calibration: keep null zones small, use close-to-linear response at first, and confirm full travel in the sim’s control settings.
  4. Assists off: turn off assisted landing, assisted yoke, and auto-rudder once you’re comfortable.
  5. Smooth frame rate: stutters during the flare cause bad landings. Lowering some graphics settings can help.
  6. Rudder control: pedals or a twist-grip stick make it far easier to stay aligned with the centerline.

Start with a Stabilised Approach

Most smooth landings are decided well before the flare. A stabilised approach means that by roughly 500 feet above the runway you are:

  • aligned with the runway centerline
  • configured: flaps set and checklist done
  • on speed: within a few knots of your target approach speed
  • on a steady descent, typically a few hundred feet per minute in a light trainer
  • trimmed, so you aren’t holding pressure on the controls

For a Cessna 172, many instructors use an approach speed around 60 to 70 knots with landing flaps, but the airplane’s handbook (POH) is the authority. Use the published speeds for your aircraft and weight.

If you’re not stabilised, go around. It’s free in the sim and a good habit. Flying a consistent traffic pattern makes stabilised approaches much easier, and good use of elevator trim keeps the airplane steady on final.

Use an Aim Point and the PAPI

  • Aim point: pick a spot on the runway, often just before the touchdown markings. If it stays fixed in the windscreen, you’re on a constant glide path. If it moves up, you’re getting low. If it moves down, you’re getting high.
  • PAPI lights: many runways have a row of four lights beside the touchdown zone. Two white and two red means you’re on a typical glide path. More white means high, more red means low.
  • Pitch for the aim point, power for the descent rate. Small, early corrections beat big, late ones.

The Flare: Where Smooth Landings Happen

  1. Over the threshold, gradually reduce power toward idle as appropriate for your aircraft.
  2. Begin the flare a short height above the runway, roughly 10 to 20 feet in a light trainer, by smoothly raising the nose to stop the descent.
  3. Shift your eyes to the far end of the runway. This gives far better height and drift cues than staring just ahead of the nose.
  4. Hold it off. As the airplane slows, keep easing back to stop it from touching down. The goal is to fly just above the runway as long as possible.
  5. Let it settle on the main wheels in a slightly nose-high attitude, with the stall warning possibly chirping in a light trainer.
  6. Keep holding back pressure and lower the nosewheel gently as speed drops.

The most common mistake is flaring too high or too abruptly, then floating, ballooning, or dropping in. The second is diving at the runway and touching down fast on the nosewheel.

After Touchdown

  • Keep straight with the rudder, not the ailerons.
  • In a crosswind, hold aileron into the wind as you slow; see crosswind landings in a flight sim.
  • Brake smoothly once the nosewheel is down.
  • Retract flaps and run the after-landing checklist once clear of the runway.

Fixing Common Problems

Problem Likely cause Fix
Hard landing Flaring late or not at all Begin the flare earlier and more smoothly; widen the field of view
Floating down the runway Too fast on final Fly the target speed; reduce power over the threshold
Balloon in the flare Pulling back too quickly Smaller, slower back pressure; if it balloons high, go around
Bounce Touching down fast or nose-first Hold attitude, add a little power and re-flare, or go around if high
Drifting sideways Crosswind or not looking far enough ahead Look down the runway; correct with aileron and rudder
Porpoising Over-controlling pitch near the ground Hold a steady landing attitude; go around if it repeats

Landing Airliners Smoothly

Airliners are flown differently in the flare:

  • They’re flown on a stable approach, often an ILS or a visual path guided by the PAPI, at a target speed set by the aircraft’s computers or performance data.
  • The flare is a small pitch change begun close to the runway, often around 20 to 30 feet in many jets. Thrust is reduced to idle as it begins.
  • The goal is a firm, controlled touchdown in the touchdown zone, not an ultra-soft one that floats down the runway.

Our A320 tutorial for MSFS covers the automation that leads you to that point. For precision approaches into the flare, see ILS approach training in Microsoft Flight Simulator.

A Practice Routine

  1. Start on a 2 to 3 mile final in calm wind using a saved flight. Fly 10 landings in a row.
  2. Note each touchdown: the speed over the threshold, the touchdown point, and how smooth it was. Several free community tools can show your landing rate, and a flight recorder tool lets you replay each touchdown from outside.
  3. Change one thing at a time, such as flare height, power reduction point, or aim point.
  4. Move to full patterns once short finals are consistent.
  5. Add wind gradually.

A few focused sessions like this usually improve landings far more than hours of random flying.

The complete guide to learn to fly

Learning to Fly with a Flight Simulator
Read the guide

Keep exploring

Guides from other topics

All topics →