If your aircraft feels twitchy, porpoises up and down on approach or won’t hold a steady bank, the problem is often your controller’s response settings rather than your flying. Microsoft Flight Simulator lets you shape how every axis responds through its sensitivity settings. This guide explains each option, gives sensible starting values, and walks through a simple tuning method.
The sensitivity screen layout differs slightly between MSFS 2020 and MSFS 2024, but the settings work the same way in both.
Why Tune Sensitivity at All?
Desktop joysticks have much shorter travel than real aircraft controls. A few millimeters of stick movement can command a large control surface deflection, so small hand movements produce big aircraft reactions. Tuning lets you:
- Soften the center, so small corrections are gentle while full deflection is still available.
- Ignore jitter from a noisy sensor or a stick that doesn’t center perfectly.
- Make sure full travel is reachable, so the throttle reaches true idle and full power.
Before You Start: Calibrate and Check for Conflicts
- Calibrate in Windows or your vendor’s software. Search Windows for “Set up USB game controllers”, open your device’s properties and confirm every axis moves smoothly through its full range and returns to center.
- Avoid double curves. If your stick’s own software (for example, Thrustmaster’s or Logitech’s) already applies a curve, either remove it there or don’t add one in the sim. Two curves stacked on top of each other are hard to reason about.
- Check for duplicate bindings. If a gamepad or a second device is also bound to pitch or roll, the two inputs can fight and feel like jitter.
Finding the Sensitivity Settings
- Open the Controls section of the sim’s options.
- Select the tab for your joystick, yoke or pedals.
- Open the Sensitivity view for that device.
- You’ll see a graph for each axis showing your current input, plus sliders for the settings below.
Changes apply to the profile currently selected for that device, so make sure you are editing the profile you actually fly with.
What Each Setting Does
Sensitivity − and Sensitivity +
These two sliders shape the response curve on each side of an axis: one for the negative half (for example, left or forward) and one for the positive half (right or back). Usually you set both to the same value.
- 0% gives a straight, linear response.
- Negative values flatten the curve near center, making small movements less sensitive while keeping full deflection at the ends. This is what most people want for pitch and roll.
- Positive values make the center more sensitive. That is rarely useful for primary flight controls.
Dead zone
The dead zone is a small area around center where input is ignored. It hides jitter and slight centering errors. Keep it as small as possible, because a large dead zone makes the aircraft feel unresponsive, and then it lurches once you pass the threshold.
Neutral
Neutral shifts the point the sim treats as center. It can correct a stick that rests slightly off-center, but recalibrating the device is usually a better fix.
Extremity dead zone
This trims the very ends of the axis, so the sim reaches 100% before the physical end of travel. It is especially useful for throttles and toe brakes that never quite reach full or zero.
Reactivity
Reactivity controls how quickly the sim follows your input. 100% follows immediately. Lower values smooth the input but introduce lag, which can lead to over-correction. Most people leave it at or near 100% for flight controls.
Suggested Starting Points by Axis
These are starting points, not rules. Every stick, aircraft and pilot is different, so adjust from here.
| Axis | Sensitivity −/+ | Dead zone | Notes |
|---|---|---|---|
| Pitch (elevator) | Mildly negative, around −20% to −40% | 0–5% | Often the axis that benefits most from a curve |
| Roll (ailerons) | Mildly negative, around −20% to −40% | 0–5% | Can match pitch or be slightly less curved |
| Rudder (pedals or twist) | Slightly negative, around −10% to −30% | Small | Helps keep taxiing from feeling twitchy |
| Throttle | 0% (linear) | None | Use extremity dead zone if idle or full power isn’t reached |
| Toe brakes | 0% or slight | Small | Extremity dead zone if brakes never reach full |
With a high-quality, contactless-sensor stick, you may need little or no dead zone. With an older potentiometer stick, a little more may be needed to stop drift.
A Step-by-Step Tuning Method
- Reset to linear. Set sensitivity to 0% and dead zone to 0% or very small.
- Pick a familiar aircraft and conditions. A light aircraft in calm weather is ideal, so the aircraft’s behavior isn’t confused with turbulence.
- Fly a few minutes of straight and level flight, then gentle turns. Note whether the aircraft feels twitchy around center.
- Add curve in small steps, around 10% at a time, to pitch and roll until small corrections feel gentle.
- Watch the input graph while holding the stick still. If the input dot wanders, add a dead zone just large enough to stop it.
- Fly a landing. Approaches and flares reveal over-sensitive pitch quickly. Our guide to landing smoothly in MSFS covers the flare itself.
- Stop when it feels predictable, not when it feels “heavy”. Too much curve can leave the aircraft sluggish and lead to over-control at the extremes.
Symptoms and Fixes
| Symptom | Likely cause | Try |
|---|---|---|
| Nose bobs up and down on approach | Pitch too sensitive near center | More negative pitch sensitivity; use trim to hold attitude |
| Aircraft drifts with stick untouched | Jitter or off-center stick | Small dead zone; recalibrate; check duplicate bindings |
| Controls feel dead, then lurch | Dead zone too large | Reduce dead zone |
| Throttle won’t reach idle or full | Axis not reaching ends | Extremity dead zone; recalibrate |
| Inputs feel delayed | Reactivity below 100% | Raise reactivity |
| Sudden changes despite a curve | Curve applied twice, or a vendor curve | Remove one of the curves |
When the Problem Is the Hardware
Settings can only do so much. Signs that the hardware itself is the issue:
- Stiction: a sticky center that makes tiny corrections jump. This is common on some yokes and budget sticks. Lubrication or modification kits help some models.
- Worn potentiometers: noisy, jumpy readings that get worse over time.
- A wobbly mount: if the stick or desk moves, inputs become inconsistent.
- Short throw: a very short stick with stiff springs is hard to control finely. An extension or a different stick may help more than any curve.
If you’re thinking about upgrading, see the best flight simulator controls for PC or our guide to choosing and setting up HOTAS flight controls.
Profiles for Different Aircraft
A light trainer, an airliner and a fighter respond very differently, and a curve that feels perfect in one may feel wrong in another. MSFS lets you save multiple profiles per device. Consider separate profiles for:
- Light aircraft: moderate curve.
- Airliners: often a little more curve, because heavy jets are flown with small, smooth inputs.
- Aerobatic or military aircraft: less curve, so full deflection comes quickly.
For an overview of how bindings and profiles are organized, see what the controls in Microsoft Flight Simulator are. Rudder pedal users should also check our rudder pedal guide for setup tips.