Three monitors arranged around you turn a flat view out of the windshield into a wraparound cockpit. You can glance left to see the runway on a downwind leg or look into a turn without touching a hat switch. Setting it up well takes some care, though. Done badly, the side screens look stretched and frame rates fall. This guide explains how to choose and arrange monitors, the two main ways to drive them, and how to configure Microsoft Flight Simulator and X-Plane.
Why Use Three Monitors?
- Peripheral vision: the side screens fill your peripheral vision, which adds a strong sense of motion and immersion.
- Looking out of the side windows: useful in the traffic pattern, where you judge turns by looking at the runway over your shoulder, and for circling approaches.
- No headset: unlike VR, you can see your physical controls, keyboard and charts, and it is comfortable for long flights.
The trade-offs are cost, desk space and a significant extra load on your graphics card.
Choosing Your Monitors
- Use three identical monitors if at all possible. Matching size, resolution, refresh rate and color makes alignment and calibration far easier.
- Thin bezels reduce the visible frame between screens.
- Size: three 27-inch monitors already give good immersion at a desk. Much larger screens add impact, but they need more distance, and the benefit tends to taper off.
- VESA mounting holes are important if you plan to use a triple monitor stand or arms. Check before buying, as not every monitor has them.
- TVs vs monitors: TVs are cheap per inch but often have more input lag and lower pixel density when viewed up close. Moderately sized TVs can work well if you sit further back.
- Avoid a two-monitor layout for the outside view, as the bezel ends up in the middle of your view.
Physical Layout and Mounting
- Center the middle screen directly in front of you at eye level, roughly where you’d see through the windshield.
- Angle the side screens inward so they wrap around you. A common approach is to angle them so you face each screen squarely when you turn your head.
- Keep the screens at the same height and as close together as the bezels allow.
- Use a sturdy stand or arms. A triple monitor stand, desk-mounted arms or a frame on a cockpit rig keeps everything aligned. Our guide to building a home cockpit covers frames and mounts.
- Fix your seating position. The views you set up in the sim only line up from one eye point, so a consistent seat position matters.
Two Ways to Run Three Screens
Spanned (Surround/Eyefinity)
NVIDIA Surround and AMD Eyefinity combine three monitors into one very wide virtual display. The sim then renders one extremely wide image.
- Pros: simple to set up, works in many games and sims, and is popular with sim racers.
- Cons: most flight sims render a spanned display as one flat image, so the edges of the side screens look stretched and distorted, especially when the screens are angled.
Separate views per monitor
The sim renders a separate camera view for each monitor: center, left and right, each rotated by a set angle. Windows treats the screens as three separate displays.
- Pros: correct perspective on each screen, so angled monitors look natural.
- Cons: more setup, and it can cost more performance, because the sim is effectively rendering several views.
For the most realistic result in flight sims, the separate-view method is usually preferred.
Setting Up Triple Monitors in Microsoft Flight Simulator
In Microsoft Flight Simulator 2020, multi-monitor views are set up through extra render windows in the sim’s experimental options. The general process is:
- Disable Surround or Eyefinity so Windows sees three separate displays, and arrange them correctly in Windows display settings.
- Run the sim on the center monitor.
- Open the options and find the experimental section, then use the option to add a new render window. A new window opens.
- Drag the window to the left monitor and make it full screen.
- Set its lateral rotation offset to a negative value so it looks left. The exact number depends on your monitor angle and field of view.
- Repeat for the right monitor with a positive offset.
- Adjust the zoom or field of view of each window until the horizon and scenery line up across the bezels from your seating position.
The sim remembers these windows, so you can remove and re-add them to switch between single and triple setups. Expect a noticeable drop in frame rate. Menus and options can change with updates, and Microsoft Flight Simulator 2024 organizes its settings differently, so check the current settings menu and official notes for your version. Some community tutorials include spreadsheets that calculate offsets and zoom from your monitor size, angle and seating distance.
Setting Up Triple Monitors in X-Plane
X-Plane has long offered built-in multi-monitor support. In its graphics settings, you can assign each monitor as a full-screen simulator view and set a lateral field-of-view offset for each one, with the side monitors offset left and right. Set the offsets to match your physical monitor angles and adjust the field of view until the views join smoothly. Exact menu names vary between X-Plane versions, so check the manual for yours.
Getting the Geometry Right
The goal is for the scenery to appear continuous across all three screens from your eye position:
- Physical angle and in-sim offset should match. If the side monitors are angled 45 degrees inward, the side views should be rotated by roughly the angle that each screen covers in your field of view.
- Field of view depends on screen size and distance. A screen that fills more of your vision should show a wider slice of the world.
- Check a straight line. Fly level over a long, straight road or runway and adjust until it doesn’t bend or jump at the bezels.
- Small errors are fine. Perfect alignment is hard. Aim for “looks natural” rather than mathematically perfect.
Performance and GPU Requirements
- Graphics card outputs: make sure your card has enough display outputs for three monitors, plus any extra screens for instruments.
- GPU load: rendering three screens, especially as separate views, can cost a large share of your frame rate. Lower settings such as cloud quality and render scaling on the side screens if needed.
- CPU load: extra views can add CPU work too, especially in busy areas.
- Matched refresh rates across the three monitors help avoid uneven motion.
For broader hardware guidance, see what hardware you need for Microsoft Flight Simulator.
Alternatives: Ultrawide, TVs and VR
- Ultrawide monitor: one curved, wide screen with no bezels, simpler to set up and lighter on performance, but with less wraparound than three angled screens.
- One large TV at a sensible distance: big and simple, but limited peripheral view.
- Head tracking on a single screen: lets you look around without extra monitors. See TrackIR vs Tobii Eye Tracker.
- VR: the most immersive option, without any screens at all. See choosing a VR headset for MSFS.
Troubleshooting
- Side screens look stretched: you are probably using Surround or Eyefinity. Switch to separate views.
- All three screens show the same view: the lateral offsets haven’t been set on the extra windows.
- Scenery doesn’t line up: adjust zoom/field of view on each window, and check your seating position.
- Windows open on the wrong screen: check the monitor order in Windows display settings, then drag each window to its correct display before making it full screen.
- Big frame-rate drop: lower graphics settings, use upscaling, or cap the frame rate at a steady value. See our MSFS performance and DLSS guide.
Triple monitors are one of several ways to improve your view. For where they fit into the wider setup, see our guide to the best flight simulator hardware.