Learn to Fly

How to Use Elevator Trim in a Flight Simulator

How to use elevator trim in MSFS and other sims: what trim does, the attitude-then-trim method, binding a trim wheel or buttons, and fixing trim that won't work.

On this page
  1. What Elevator Trim Does
  2. Why Trim Matters So Much
  3. How to Trim: Attitude First, Then Trim
  4. Setting Up Trim Controls in MSFS
  5. Why Trim Feels Different on Sim Hardware
  6. Trim in Each Phase of Flight
  7. Trim in Airliners and Fly-by-Wire Aircraft
  8. Troubleshooting Trim Problems

Elevator trim is the control that turns a twitchy, hard-work airplane into one that flies itself straight and level while you look outside, tune radios, or fly an approach. Many new simmers either ignore trim or fight with it, then wonder why holding altitude is so hard. This guide explains what trim does, how to use it properly, and how to set it up in Microsoft Flight Simulator and similar sims.

What Elevator Trim Does

In a typical light aircraft, a small trim tab on the trailing edge of the elevator holds the elevator in a chosen position. Some aircraft move the whole horizontal stabilizer instead. Once you’ve trimmed, the airplane holds that pitch attitude and airspeed without you pushing or pulling on the yoke.

The important idea: trim sets an airspeed, not an altitude. A well-trimmed light airplane will try to return to its trimmed speed. If you add power, it’ll tend to climb at about the same speed. Reduce power and it’ll tend to descend at about the same speed. That’s why trim makes everything from cruise to approach more stable. The underlying aerodynamics are covered in principles of flight and aircraft flight controls.

Why Trim Matters So Much

  • Precision: with no constant pressure to hold, small corrections are much easier.
  • Workload: your hands and attention are free for navigation, radios, and checklists.
  • Stable approaches: a trimmed approach makes smooth landings far more likely.
  • Instrument flying: holding altitude on instruments without trim is exhausting.

How to Trim: Attitude First, Then Trim

The classic sequence is “pitch, power, trim”:

  1. Set the attitude you want with the elevator, for example level flight.
  2. Set the power for that phase of flight.
  3. Let the airplane settle, giving it a few seconds for speed to stabilise.
  4. Trim in small increments to remove the pressure you’re holding.
  5. Test it: relax your grip. If the nose rises or falls, trim a little more and repeat.

Don’t use trim to fly the airplane. Fly with the elevator, then trim to relieve pressure. Rolling the trim to change attitude leads to over-corrections and wandering altitude.

Setting Up Trim Controls in MSFS

Choosing a trim control

  • A trim wheel (separate or built into a throttle quadrant) is closest to the real thing in many light aircraft.
  • Two buttons or a hat switch on your yoke or stick work well and are easy to reach.
  • A spare axis or rotary can be mapped as a trim axis.

The main thing is that you can trim without looking away from your scan.

Binding it

In MSFS, open the Controls options, select your device, and search for elevator trim. Our overview of the controls in Microsoft Flight Simulator explains how the menu is organized. The relevant functions include:

  • Elevator trim up / down for buttons or a hat switch
  • Elevator trim axis for a wheel or rotary that reports position

You can also check the default keyboard bindings for elevator trim on the keyboard profile page. They’re often on the number pad, but layouts vary, so confirm them in your own settings.

Tips:

  • If buttons trim too slowly or too quickly, some aircraft and tools let you adjust the trim rate.
  • Make sure trim isn’t bound twice, for example to a wheel axis and a joystick slider, or the bindings will fight each other.

Assists to turn off

MSFS has assistance options that can manage trim or pitch for you, depending on the version and settings. They’re useful for casual flying. If you’re learning, though, switch off any auto-trim or similar pitch assist so you’re actually controlling the airplane.

Why Trim Feels Different on Sim Hardware

In a real airplane, trim changes the force you feel on the yoke. In a sim with a spring-centered stick or yoke, the springs always pull toward center no matter how the airplane is trimmed. So in the sim, “trimmed” means the airplane holds its attitude with your controls at center, rather than with zero force.

In practice: if you’re holding the stick slightly back to stay level, trim nose-up until you can let it return to center and the airplane still holds. Force-feedback controls can simulate changing forces more realistically, but they’re far from universal.

Trim in Each Phase of Flight

Phase What to do
Takeoff Set takeoff trim per the checklist before departing (often a marked position)
Climb Pitch for climb speed, then trim nose-up to hold it
Level-off Lower the nose, let speed build, reduce power to cruise, then trim nose-down
Descent Reduce power and hold your speed; adjust trim as needed
Approach Each flap stage changes pitch; re-trim after each change
Go-around Expect a strong nose-up tendency when you add full power with nose-up trim; push forward, then re-trim

The go-around case matters. In a real airplane, failing to hold forward pressure with landing trim set and full power applied can cause an “elevator trim stall.” Practise that in the sim; our guide to power-on and power-off stalls has more on stall awareness.

Trim in Airliners and Fly-by-Wire Aircraft

  • Conventional jets typically use electric trim switches on the yoke that move the horizontal stabilizer, plus a manual trim wheel. The autopilot trims automatically when engaged.
  • Airbus fly-by-wire aircraft like the A320 trim automatically in normal flight. The pilot doesn’t trim the way a Cessna pilot does. See our A320 tutorial for MSFS.

If you mainly fly airliners, it’s still worth learning manual trim in a light aircraft, because it builds the pitch-and-power understanding behind everything else.

Troubleshooting Trim Problems

Problem Possible cause Fix
Trim does nothing Not bound, or bound in a different profile Check the active controls profile for your device
Trim jumps back after you release A trim axis and trim buttons both bound Remove one binding
Trim moves too slowly Default button trim rate Hold the button longer, or use an axis or wheel
Airplane won’t stay trimmed Power or configuration still changing Let speed settle before trimming
Trim moves on its own Autopilot engaged, or an auto-trim assist on Disengage the autopilot or turn off the assist
Nose pitches up hard on go-around Nose-up trim plus full power Hold forward pressure, then trim

Once trim feels natural, everything from the traffic pattern to ILS approaches gets easier.

The complete guide to learn to fly

Learning to Fly with a Flight Simulator
Read the guide

Keep exploring

Guides from other topics

All topics →