The Airbus A320 is one of the most popular airliners to fly in Microsoft Flight Simulator 2020. Its automation is also the part that confuses newcomers most. Knobs that you push and pull, a strip of green and blue text across the top of the display, thrust levers that click into detents: it all works logically once you see the pattern. This tutorial focuses on the flight director and autopilot, the core of flying the A320 well.
Which A320 to Use in MSFS 2020
The most widely used option is the free FlyByWire A32NX, a community project that started from the default A320neo and has been developed into a much more complete simulation. It’s available through the FlyByWire installer, and its online documentation is detailed. The steps below follow standard Airbus logic, which applies to the A32NX and broadly to other A320 add-ons. Menus and some behaviour can change with updates, so check the documentation for your version. For a comparison of the options, see what is the best A320 for MSFS 2020.
This tutorial assumes the aircraft is powered, the flight plan is entered in the MCDU, and performance data such as takeoff speeds and flex temperature has been calculated. Many simmers use a planning tool such as SimBrief and import the plan.
The Key Controls: FCU, FMA, and Thrust Levers
The FCU and the push/pull logic
The flight control unit (FCU) on the glareshield has four main knobs: SPD/MACH, HDG/TRK, ALT, and V/S / FPA. Each knob can be pushed or pulled:
- Push = managed. The aircraft follows the flight plan and performance data from the flight management system. A managed value shows as dashes with a white dot beside the window.
- Pull = selected. The aircraft follows the value you’ve dialled in on the FCU.
For example, pushing the HDG knob arms or engages NAV to follow the flight plan route, while pulling it flies the heading you’ve set. Pushing the ALT knob gives a managed climb (CLB) or descent (DES) that respects altitude constraints. Pulling it gives an open climb or descent (OP CLB / OP DES) straight to the FCU altitude, ignoring constraints.
Other buttons on the FCU include AP1, AP2, A/THR, LOC, APPR, and EXPED. The FD and LS buttons sit on each pilot’s EFIS control panel.
The flight mode annunciator (FMA)
The strip across the top of the primary flight display is the FMA, and reading it is the most important A320 habit. It has five columns, from left to right:
- Autothrust mode, such as SPEED, THR CLB, or MAN FLX
- Vertical mode, such as SRS, CLB, ALT, DES, or G/S
- Lateral mode, such as RWY, NAV, HDG, or LOC
- Approach capability, such as CAT 1 or CAT 3 DUAL
- Engagement status, such as AP1, 1 FD 2, or A/THR
Green text shows active modes; blue (cyan) text shows armed modes waiting to engage. A box around a mode means it has just changed. Whenever you press something on the FCU, look at the FMA to confirm the airplane did what you expected.
Thrust lever detents and autothrust
The A320 thrust levers don’t move on their own. Instead they click into detents:
- TOGA: maximum takeoff/go-around thrust
- FLX/MCT: reduced (flex) takeoff thrust, or maximum continuous thrust
- CL: climb, the normal position for autothrust in flight
- IDLE
With autothrust active, the levers sit in the CL detent and the computers vary thrust up to the climb limit. If your hardware throttle doesn’t have detents, set up the detent ranges in the aircraft’s throttle configuration so the sim knows which lever position matches which detent.
The Flight Director on the A320
The flight director shows guidance on the PFD as two green bars, one for pitch and one for roll. Fly the aircraft symbol into the center of the bars and you’re following the guidance. FD1 drives the captain’s PFD and FD2 the first officer’s. Both are normally on.
In TRK/FPA mode, selected with a button on the FCU, the bars are replaced by the flight path vector (“the bird”) and a flight path director. Close to the ground on takeoff and landing, a yaw bar can appear to guide rudder inputs on the runway. For the general concept, read what is an aircraft flight director.
Takeoff with the Flight Director
- Check both FDs are on. The FMA should show 1 FD 2 in the right column.
- Set the FCU altitude to your initial cleared altitude.
- Advance the thrust levers to about 50% N1, let the engines stabilise, then move them to FLX/MCT (or TOGA).
- Check the FMA: MAN FLX (or MAN TOGA), SRS for pitch guidance, RWY for runway centerline guidance, and NAV armed in blue if a departure is loaded.
- At rotation speed, rotate smoothly and follow the pitch bar. SRS guides you to hold a safe speed above V2.
- At the thrust reduction altitude, the FMA flashes LVR CLB. Pull the thrust levers back to the CL detent. Autothrust becomes active and the FMA shows THR CLB.
Engaging the Autopilot and Climbing
Once safely airborne and climbing, a short time after liftoff and above a minimum height, press AP1. The FMA shows AP1, and the autopilot now follows the same guidance the FD bars were showing.
- For a managed climb respecting departure constraints, push the ALT knob. The FMA shows CLB.
- For an unrestricted climb to the FCU altitude, pull the ALT knob. The FMA shows OP CLB.
- To follow a heading from ATC, turn the HDG knob to the heading and pull it. The FMA shows HDG. Push it later to rejoin NAV.
- Climbing through the transition altitude, set standard pressure with the baro knob (STD). Our guide to flight levels vs altitude explains why.
Cruise and Descent
At cruise, the FMA typically shows SPEED, ALT CRZ, and NAV. Before the top of descent:
- Set the FCU altitude to your cleared lower altitude.
- Push the ALT knob near the top-of-descent marker for a managed DES, or pull it for OP DES if ATC asks you to descend now.
- Use V/S (pull the V/S knob) for a fixed rate when you need finer control.
- Set the destination’s local altimeter setting as you pass the transition level.
Flying the ILS and Autoland Basics
- Make sure the approach is loaded and the ILS frequency and course are tuned on the MCDU’s radio navigation page.
- Press LS on the EFIS panel to display the localizer and glideslope scales.
- Once cleared and on an intercept heading, press APPR. The FMA shows G/S and LOC armed in blue.
- The localizer and glideslope capture as LOC* and G/S*, then show steady as LOC and G/S.
- For an autoland, engage AP2 as well as AP1, so the FMA shows CAT 3 DUAL capability where available. Manage speed and configuration with flaps and gear as you slow down.
- Near the ground the FMA moves through LAND, FLARE, and ROLL OUT. Retard the thrust levers to idle when prompted.
For a deeper look at ILS technique, see ILS approach training in Microsoft Flight Simulator.
Hand-Flying: When to Turn the FDs Off
Hand-flying with the flight directors on is fine as long as they’re giving guidance you intend to follow. If you’re flying visually or following your own raw-data plan, turn both FDs off. Otherwise you’ll find yourself “chasing the bars” toward a mode you didn’t intend. With both FDs off and the bird displayed, autothrust switches to speed mode, which many pilots find helpful for visual approaches.
Common Mistakes in the Sim
- Not reading the FMA. Most “the autopilot did something weird” moments come from an unnoticed mode change.
- Thrust levers not in CL. If your hardware lever sits between detents, autothrust may be limited or act unexpectedly.
- Pressing APPR too early or too late. Arm it once you’re cleared for the approach and on an intercept heading, not 100 miles out.
- Forgetting the FCU altitude. The aircraft won’t climb or descend past the FCU altitude. Always set it first.
- Mixing managed and selected unintentionally. A pull when you meant to push sends you off the flight plan.
- Ignoring STD and QNH changes. These cause level busts on online networks.
If you’re curious how far the A320 can take you once you’ve mastered the automation, read can an A320 fly over the Atlantic.