The 3-to-1 rule in one line
To find your top of descent (TOD), take the altitude you need to lose in thousands of feet and multiply by 3. The answer is roughly how many nautical miles before your target you should start down.
Distance to start descent (NM) ≈ (altitude to lose ÷ 1,000) × 3
The rule works because a 3-degree descent path loses close to 300 feet per nautical mile, or about 1,000 feet every 3 miles. It’s the same angle as a typical ILS glideslope, which makes it comfortable for passengers and easy to fly in most aircraft.
Step by step: calculating top of descent
- Pick your target. This is where you want to reach a lower altitude: pattern altitude at a destination airport, a crossing altitude at a fix, or the altitude where an approach starts.
- Work out the altitude to lose. Cruise altitude minus target altitude.
- Divide by 1,000 and multiply by 3. That gives the distance in nautical miles from the target.
- Add a buffer. Allow extra miles for slowing down, configuring the aircraft or a tailwind. Many pilots add a few miles as a margin.
- Mark the point. Note it on your flight plan, as a distance from a waypoint, or set it in your GPS or FMC.
Worked examples
Light aircraft into a small airport
- Cruise altitude: 7,500 feet
- Destination field elevation: 500 feet, with a pattern altitude of about 1,000 feet above the field, so 1,500 feet
- Altitude to lose: 7,500 − 1,500 = 6,000 feet
- 3-to-1 rule: 6 × 3 = 18 NM
- With a few miles’ buffer, start down about 20 NM from the airport.
Airliner to the start of an approach
- Cruise altitude: 35,000 feet
- Target: 3,000 feet at the point where the approach begins
- Altitude to lose: 32,000 feet
- 3-to-1 rule: 32 × 3 = 96 NM
- Add distance to slow down (see below), and start descending roughly 100 to 110 NM out, or earlier with a tailwind.
Working out the descent rate
Once you know where to start, you need a vertical speed that holds roughly a 3-degree path. A quick rule:
Descent rate (ft/min) ≈ groundspeed (knots) × 5
This is the same as halving your groundspeed and adding a zero. At 120 knots, that’s about 600 feet per minute. At 300 knots, about 1,500 feet per minute. At 450 knots, about 2,250 feet per minute. The rule slightly underestimates a true 3-degree path, but it’s close enough for planning.
As groundspeed falls during the descent, the required rate falls with it, so revisit the number as you slow down.
The time-based method
Some pilots, especially in light aircraft, prefer to choose a comfortable descent rate first, such as 500 feet per minute, and work out the distance from that:
- Time to descend = altitude to lose ÷ descent rate.
- Distance = time (minutes) × groundspeed ÷ 60.
Using the light aircraft example: 6,000 feet at 500 ft/min takes 12 minutes. At a groundspeed of 120 knots (2 NM per minute), that’s 24 NM. That’s further out than the 3-to-1 answer, because 500 ft/min at 120 knots is a shallower path than 3 degrees. Either approach works; just be consistent.
Adjusting for wind, slowing down and restrictions
Wind. A tailwind raises your groundspeed, so you cover more distance for the same altitude lost. Start down earlier. A headwind does the opposite, so you can start a little later. Increasing the descent rate in a tailwind also works, within the aircraft’s limits.
Slowing down. Jets can’t descend steeply and slow down at the same time without help from speed brakes. A commonly used rule of thumb is to add about 1 NM for every 10 knots you need to lose in level flight. In the US, aircraft are generally limited to 250 knots below 10,000 feet, so airline pilots often plan to reach 10,000 feet with some distance to spare for slowing to that speed.
Restrictions along the arrival. If your STAR or ATC requires you to cross a fix at a certain altitude, plan the descent to that fix, not to the airport. A restriction can move your top of descent much earlier. Our guide to reading SID and STAR charts explains how restrictions are shown.
Short flights. On a short route, you may barely reach cruise before it’s time to descend. In that case a lower cruise altitude is often better. See how to create a flight plan for choosing a cruise altitude.
Checking your descent as you go
The 3-to-1 rule also works in reverse during the descent. At any point, multiply your remaining distance to the target by about 333 (or divide by 3 and add three zeros) to get how many feet above the target you should be.
- 30 NM from the target, you should be about 10,000 feet above it.
- 15 NM out, about 5,000 feet above.
If you’re higher than that, you’re high: increase the descent rate, use speed brakes if available, or ask ATC for more distance. If you’re lower, reduce the descent rate or level off briefly.
Quick reference table
Distances below use the plain 3-to-1 rule with no buffer.
| Altitude to lose | Distance from target |
|---|---|
| 3,000 ft | 9 NM |
| 5,000 ft | 15 NM |
| 8,000 ft | 24 NM |
| 10,000 ft | 30 NM |
| 20,000 ft | 60 NM |
| 30,000 ft | 90 NM |
| 35,000 ft | 105 NM |
| Groundspeed | Approx. 3° descent rate |
|---|---|
| 90 kt | 450 ft/min |
| 120 kt | 600 ft/min |
| 200 kt | 1,000 ft/min |
| 300 kt | 1,500 ft/min |
| 450 kt | 2,250 ft/min |
Top of descent in your simulator’s avionics
Many sim aircraft calculate TOD for you, but knowing the rule lets you check them:
- Airliner FMCs in detailed sim aircraft usually show a T/D marker on the navigation display once the route, cruise altitude and arrival restrictions are entered.
- Glass cockpit GPS units such as G1000-style avionics often include vertical navigation or a vertical calculator that gives a top of descent alert for a target altitude and distance.
- Planning tools such as SimBrief list TOD in the flight log, and Little Navmap can show it on its route elevation profile.
If the avionics and your mental math disagree by a lot, check for a missing altitude restriction or a wrong cruise altitude in the FMC. For more on the tools, see our flight planning software guide, and for where descent sits in the flight as a whole, see the 7 phases of flight.