Flight Planning

How to Make Flight Plans in GeoFS

Create a flight plan in GeoFS: add waypoints in the Nav panel, set altitudes and speeds, fly it with the autopilot's NAV mode and finish on an ILS approach.

On this page
  1. How flight plans work in GeoFS
  2. Creating a flight plan step by step
  3. Setting altitudes and speeds for each waypoint
  4. Flying the plan with the autopilot
  5. Adding an ILS approach at the destination
  6. Importing routes from SimBrief and community files
  7. A simple example route
  8. Troubleshooting

How flight plans work in GeoFS

GeoFS is a browser-based flight simulator, and its flight plan system is simpler than the flight management computers in desktop sims. A GeoFS flight plan is a list of waypoints. Each one can have a target altitude and speed, and the autopilot can follow them in order when it’s in NAV mode.

Waypoints can be airports, runways, radio navaids, named fixes or plain coordinates. That’s enough to fly a realistic route from one airport to another, finish with an ILS approach, and practice the same planning habits used in bigger simulators.

GeoFS is updated regularly, so button positions and labels may differ slightly from what’s described here. If you haven’t tried it yet, see is GeoFS free to play? for what’s included.

Creating a flight plan step by step

  1. Open GeoFS in your browser and pick your aircraft and starting airport.
  2. Open the Nav panel from the menu at the bottom of the screen, then select Flight plan. This is GeoFS’s flight management panel.
  3. Add your departure. Type the departure airport’s ICAO code (for example KSFO) or select the departure runway.
  4. Add en route waypoints. Type the identifiers of fixes or navaids along your route, or enter coordinates. Add them in the order you want to fly them.
  5. Add your destination airport or arrival runway as the last waypoint.
  6. Enter an altitude and speed for each waypoint (see the next section). Type altitudes in feet without commas, for example 12000, and speeds in knots.
  7. Check the route on the map. Look for zigzags or a waypoint in the wrong country, which usually means a typo or an identifier that exists in more than one place.

Our general guide on how to create a flight plan explains how to pick a sensible route and altitude in the first place.

Setting altitudes and speeds for each waypoint

This is where most GeoFS flight plans go wrong. The autopilot will try to reach each waypoint’s altitude, so the numbers need to make sense for your aircraft:

  • Climb gradually. Give the first few waypoints stepped altitudes rather than asking for cruise altitude at the first fix. An airliner can’t reach 35000 feet five miles after takeoff.
  • Cruise level. Keep the same altitude and speed for the middle waypoints.
  • Descend early. Start stepping altitudes down well before the destination. A common rule of thumb is to allow about 3 nautical miles for every 1,000 feet you need to lose. Our guide to calculating top of descent explains the method.
  • Slow down before the approach. Reduce speed on the last few waypoints so you’re at a sensible approach speed when you intercept the ILS.
  • Match the aircraft. A Cessna 172 cruises far slower and lower than a Boeing 777. Use speeds and altitudes the aircraft can actually achieve.

Thinking about the flight in phases (climb, cruise, descent, approach) makes these numbers easier to choose. See what are the 7 phases of flight? for a breakdown.

Flying the plan with the autopilot

  1. Take off and climb manually, or with the autopilot’s basic modes, to a safe height.
  2. Engage the autopilot.
  3. Switch the autopilot to NAV mode. The aircraft should turn toward the active waypoint and follow the plan in sequence.
  4. Watch the first few waypoints to confirm it’s tracking correctly and climbing as expected.
  5. Keep an eye on speed and altitude through the flight. GeoFS’s autopilot is helpful, but it’s not a full airliner FMC, and it can still overspeed or stall if the targets you’ve set are unrealistic.

Adding an ILS approach at the destination

If your destination runway has an ILS, you can add it to the end of the flight plan so the aircraft lines up with the runway automatically. Add the destination runway’s ILS as the final element of the plan, make sure you arrive at the last waypoint low and slow enough to intercept it, and let the autopilot capture the localizer and glideslope. Disconnect the autopilot for the flare and touchdown, or earlier if you prefer to hand-fly the approach.

Importing routes from SimBrief and community files

Typing every waypoint gets tedious on long flights. Two shortcuts exist:

  • SimBrief import. GeoFS has offered a way to link a SimBrief username in its options and then import your latest SimBrief plan from the flight plan panel. Build the plan on SimBrief first, then import it.
  • Route files. Some players share GeoFS-compatible route files (JSON format) for popular routes, and these can be uploaded into the flight plan panel.

Check the imported route on the map before you depart. Imported plans may lack the per-waypoint altitudes and speeds the GeoFS autopilot uses, so you might need to fill those in.

A simple example route

Here’s the shape of a short airliner hop, using made-up numbers you can adapt to any pair of nearby airports roughly 150 nautical miles apart:

Waypoint Altitude (ft) Speed (kt) Phase
Departure runway – – Takeoff
First fix, about 10 NM out 6000 220 Climb
Second fix 15000 280 Climb
Cruise fixes 24000 300 Cruise
Fix about 60 NM from destination 18000 280 Descent
Fix about 30 NM from destination 9000 250 Descent
Fix about 15 NM from destination 4000 200 Approach
Destination runway ILS – – Approach and landing

Check that the descent fits: dropping from 24000 to about 3000 feet means losing roughly 21,000 feet, which the 3-to-1 rule puts at about 63 nautical miles.

Troubleshooting

  • The aircraft ignores the plan. Confirm the autopilot is on and in NAV mode, not heading mode.
  • It turns the wrong way or flies to the wrong place. An identifier may match a fix or navaid somewhere else in the world. Check each waypoint on the map.
  • It climbs or dives aggressively. The altitude targets between waypoints are too far apart for the distance. Add intermediate waypoints or spread the altitude change out.
  • It’s too fast or too high for the ILS. Start your descent and slow down earlier, and add another waypoint before the approach.

The complete guide to flight planning

Flight Planning Software for Flight Simulators
Read the guide

Keep exploring

Guides from other topics

All topics →