Flight Planning

How do you create a flight plan?

Create a flight plan step by step: check weather, build a VFR or IFR route, pick an altitude, work out fuel, file it and load it into your flight simulator.

On this page
  1. Short answer
  2. Step 1: Decide where you’re going and how
  3. Step 2: Check the weather
  4. Step 3: Build the route
  5. Step 4: Choose a cruise altitude
  6. Step 5: Work out time and fuel
  7. Step 6: Check weight and the aircraft’s limits
  8. Step 7: File the plan
  9. Step 8: Load the plan into your simulator
  10. A worked example

Short answer

To create a flight plan, you:

  1. Decide where you’re going, in what aircraft, and whether you’ll fly VFR (by visual reference) or IFR (by instruments).
  2. Check the weather at departure, destination and along the route.
  3. Build a route: visual checkpoints for VFR, or departure procedure, airways and arrival for IFR.
  4. Choose a cruise altitude that suits the aircraft, terrain, winds and altitude rules.
  5. Work out flight time and fuel, including reserves.
  6. Check the aircraft’s weight is within limits.
  7. File the plan with ATC (real world, the sim’s ATC, or an online network).
  8. Load the route into the aircraft’s GPS or flight management computer.

You can do all of this with paper charts and a calculator, or let flight planning software handle most of it. The steps below explain each part, with notes on how it works in a simulator.

Step 1: Decide where you’re going and how

Start with the basics: departure airport, destination, aircraft and the type of flight.

  • VFR flights navigate by looking outside, using landmarks and, optionally, GPS. They suit light aircraft in good weather and shorter distances.
  • IFR flights follow published procedures and airways under ATC control, using instruments. Airliners fly IFR, and it’s the way to go if the weather is poor.

For IFR, also choose an alternate airport in case you can’t land at the destination. In the sim, pick a realistic pairing: a Cessna 172 is great for a 100-mile hop, not a transatlantic crossing.

Step 2: Check the weather

Look at current reports (METARs) and forecasts (TAFs) for your departure and destination, and winds aloft for your route. Weather drives many later decisions: which runways are likely in use, whether VFR is sensible, what altitude gives the best winds, and how much fuel you’ll need.

In a simulator, decide whether you’re flying with live real-world weather or a preset. If you use live weather, real METARs will match what you see in the sim reasonably well.

Step 3: Build the route

For VFR: draw a line on a chart from departure to destination, then pick visual checkpoints along it every 5 to 15 minutes or so, such as towns, lakes, rivers, highways or distinctive terrain. Steer around restricted airspace and high terrain. Our guide to planning a VFR cross-country flight in a simulator covers this in depth.

For IFR: a typical route has three parts:

  • a SID (standard instrument departure) from the departure runway to the en route structure,
  • airways or direct waypoints in the middle,
  • a STAR (standard terminal arrival route) toward the destination, followed by an instrument approach.

Planners such as SimBrief can generate IFR routes automatically. If you want to understand the procedures they pick, see how to read SID and STAR charts.

Step 4: Choose a cruise altitude

Consider:

  • Aircraft performance. Piston singles usually cruise a few thousand feet up; jets cruise much higher, at flight levels.
  • Distance. Short flights don’t benefit from a long climb to a high altitude.
  • Terrain and obstacles. Stay well clear of the highest terrain along the route.
  • Winds. A tailwind at one altitude can make a big difference to time and fuel.
  • Altitude rules. Many countries use a semicircular (hemispheric) rule so aircraft flying in opposite directions are separated. In the US, for example, VFR flights above 3,000 feet above ground level fly at odd thousands plus 500 feet (such as 5,500) on magnetic courses from 0 to 179 degrees, and even thousands plus 500 feet (such as 6,500) on courses from 180 to 359 degrees. IFR flights use whole thousands on the same pattern. Other countries have their own rules.

Step 5: Work out time and fuel

For each leg, work out your groundspeed (true airspeed adjusted for wind), then time = distance ÷ groundspeed. Add the legs together for total flight time, then calculate fuel from the aircraft’s burn rate, plus taxi fuel, reserves and alternate fuel for IFR. Our flight sim fuel calculator guide explains each component with a worked example.

Plan your descent too. A rough top of descent point is easy to work out with the 3-to-1 rule.

Step 6: Check weight and the aircraft’s limits

Add up the empty weight, crew and passengers, baggage and fuel, and check the total is within the aircraft’s maximum takeoff weight and center of gravity limits. In a light aircraft, full fuel and four adults may not fit within limits. In a sim, the aircraft’s weight and balance screen or EFB usually shows this for you.

Step 7: File the plan

  • Real world: pilots file through their aviation authority’s service or an approved app. In the US, VFR flight plans are optional but recommended; IFR flight plans are required to fly in controlled airspace under IFR.
  • Sim ATC: in MSFS, you file the plan with the built-in ATC from the flight planning screens; see our MSFS 2024 flight planner guide.
  • Online networks: on VATSIM or IVAO, you file through the network’s flight plan form or prefile from a planner like SimBrief. You’ll need the aircraft type, equipment codes, route, altitude, speed, fuel endurance and alternate.

Step 8: Load the plan into your simulator

The final step is getting the route into the aircraft:

Check the loaded route on the map before departure. Missing or misplaced waypoints are much easier to fix on the ground.

A worked example

Here’s how a short IFR flight in a simulated regional jet might come together:

  1. Plan: two airports about 250 nautical miles apart, with a nearby alternate.
  2. Weather: destination forecast shows low cloud, so IFR it is, and the alternate has better weather.
  3. Route: the planner picks a SID from the expected departure runway, two airways, and a STAR into the destination.
  4. Altitude: for this distance the planner suggests a mid-20s flight level, which suits the aircraft and gives a short cruise.
  5. Fuel: trip fuel, plus contingency, alternate and final reserve, gives a block fuel figure on the briefing.
  6. Weight: passengers and cargo keep the aircraft under its maximum takeoff and landing weights.
  7. File: the plan is filed on the online network with the correct equipment string.
  8. Load: the route is imported into the aircraft’s FMC, and the SID and approach are checked against the charts.

Once you’ve done this a few times, it takes minutes. Understanding each step means you can catch mistakes in a generated plan rather than flying it blindly.

The complete guide to flight planning

Flight Planning Software for Flight Simulators
Read the guide

Keep exploring

Guides from other topics

All topics →