Why plan a VFR cross-country in a sim
A VFR cross-country is a flight from one airport to another, navigating mainly by looking outside: following landmarks on a chart, holding headings and checking your time. Real student pilots spend a lot of training on it. In a simulator, it’s one of the most satisfying ways to fly a light aircraft, and the planning is half the fun.
You can fly VFR in any sim just by pointing the aircraft at the destination. Planning properly turns the flight into a navigation exercise and builds skills that carry over to real flying.
This guide follows the same steps real pilots use, adapted for a simulator. It’s for sim practice, not real-world flight planning.
Step 1: Choose the aircraft, airports and distance
- Aircraft: a simple trainer such as a Cessna 172 or Piper PA-28 keeps workload manageable.
- Airports: pick a departure and destination roughly 50 to 150 nautical miles apart. That’s long enough to need navigation, short enough to finish in an hour or so.
- Region: an area with distinctive landmarks, such as coastlines, rivers, lakes or mountains, makes the first few flights easier. Areas with detailed scenery in your sim help too.
- Alternates: note one or two airports along the route you could divert to.
Step 2: Get charts and study the airspace
Real VFR pilots use sectional or equivalent aeronautical charts. For sim flying:
- SkyVector shows US sectional charts free in a browser, and is useful for drawing a route line.
- Little Navmap shows airspace, airports and navaids from your sim’s own database, which means what you see should match what’s in the sim.
- National authorities in many countries publish VFR charts or airspace maps, some free.
Look along your route for controlled airspace, restricted and military areas, high terrain and tall obstacles. The sim won’t stop you flying through restricted airspace, but avoiding it is part of the exercise, and on online networks controllers will notice.
Step 3: Pick checkpoints the sim actually shows
Choose visual checkpoints every 5 to 15 minutes along the route. Good choices are big and distinctive:
- lakes, reservoirs and coastlines,
- rivers and major river bends,
- highways and railway lines, especially where they cross,
- towns and cities,
- mountains, ridges and valleys,
- other airports.
This is where sim planning differs from real-world planning. Simulator scenery is built from satellite imagery, map data and automatically generated buildings, and it doesn’t always show small features. A water tower or a minor road on the chart may not exist in the sim, and some features may look different. Favor large natural features and major roads, and if you’re unsure, fly the route once at high sim speed or check the area in the sim’s map before relying on a checkpoint.
Step 4: Measure courses and distances
For each leg between checkpoints, measure:
- Distance in nautical miles.
- True course, the direction of the line relative to true north.
- Magnetic course, which corrects true course for magnetic variation shown on the chart. A common memory aid is “east is least, west is best”: subtract easterly variation, add westerly variation.
Planning tools such as Little Navmap and SkyVector show distances and courses automatically, but working at least one leg by hand helps you understand what the numbers mean.
Step 5: Choose an altitude
Pick an altitude that keeps you well clear of terrain and obstacles, below any airspace you don’t want to enter, and comfortably below the cloud base if you’re using real weather.
Many countries use a rule that separates opposite-direction traffic by altitude. In the US, for example, VFR flights above 3,000 feet above ground level fly odd thousands plus 500 feet (such as 5,500) on magnetic courses of 0 to 179 degrees, and even thousands plus 500 feet (such as 6,500) on courses of 180 to 359 degrees. Other countries have their own rules.
Step 6: Check the sim weather and correct for wind
Decide whether you’ll fly with live weather or a preset. With live weather, look up the METAR for your departure and destination and the winds aloft near your planned altitude. With a preset, set a wind you can plan around.
Wind pushes the aircraft off course, so you need a wind correction angle: a few degrees into the wind to stay on track. It also changes your groundspeed. You can work these out with an E6B flight computer, an E6B app or an online wind triangle calculator, using your true course, true airspeed and the wind direction and speed. Apply the wind correction to the magnetic course to get the magnetic heading you’ll actually fly.
Step 7: Fill in a navigation log
A navigation log puts everything in one place. Here’s an example with illustrative numbers for a 110-knot trainer and a wind from the left:
| Leg | Mag course | Wind correction | Mag heading | Distance | Groundspeed | Time |
|---|---|---|---|---|---|---|
| Departure to lake | 065° | −4° | 061° | 18 NM | 102 kt | 11 min |
| Lake to highway junction | 072° | −4° | 068° | 24 NM | 103 kt | 14 min |
| Junction to river bridge | 090° | −3° | 087° | 21 NM | 106 kt | 12 min |
| Bridge to destination | 080° | −4° | 076° | 15 NM | 104 kt | 9 min |
Add columns for estimated and actual times over each checkpoint, so you can compare during the flight. Leave space for fuel and radio frequencies too.
Step 8: Plan fuel and alternates
Add up the leg times, add a few minutes for the climb, then multiply by the aircraft’s fuel burn at your planned power setting. Add taxi fuel and a reserve. In the US, the legal VFR minimum is 30 minutes of reserve fuel by day and 45 minutes at night, and many instructors suggest carrying more. Our flight sim fuel calculator guide has a worked example.
Note your alternates on the nav log, with a rough heading and distance from the midpoint of the route.
Step 9: Set up the sim
- Load fuel and weight to match your plan.
- Set weather and time of day. Daylight and good visibility make a first flight easier.
- Enter a VFR flight plan if you want the sim’s map or ATC to know about it. In MSFS, you can build a VFR route in the flight planner or EFB; see our MSFS 2024 flight planner guide. In X-Plane, you can load a route into the GPS with a tool from our flight planning software guide.
- Decide how many aids you’ll use. For real pilotage practice, hide the in-sim map, turn off GPS route lines or leave the GPS unused, and disable any on-screen markers or labels.
- Keep your chart and nav log handy on a second screen, tablet or paper.
Flying the plan
- Take off and set course. Note the time when you depart or when you’re established on your first heading.
- Fly the heading and watch the clock. Hold your planned magnetic heading and altitude, and look for each checkpoint at its estimated time.
- Confirm each checkpoint. Check that what you see matches the chart: shape of a lake, direction of a road, position of a town relative to your track.
- Adjust. If you’re consistently left or right of course, the wind is different from forecast. Adjust your heading and update your estimates.
- If you’re unsure of your position, don’t wander. Hold your heading, look for a large landmark or a feature you can identify, and use radio navaids or the GPS as a backup. In a sim, there’s no shame in pausing to check the map, then trying again without it.
- Plan the arrival. Work out when to start descending (our guide to calculating top of descent explains the method), listen to the destination weather, and join the traffic pattern for the runway in use.
Making it more realistic
- Fly on an online network. On VATSIM or IVAO, you can file a VFR flight plan and request traffic advisories (often called flight following in the US) from controllers where they’re online.
- Add failures. Some sims let you fail the GPS or radios mid-flight, forcing you to rely on pilotage.
- Fly in less-than-perfect weather. Lower visibility or gusty winds make checkpoint spotting and wind correction more challenging.
- Fly the flight in real time. Keeping sim speed at 1x makes timing and fuel planning meaningful.
For the general planning process behind any route, see how do you create a flight plan?, and for how the flight breaks into stages, see the 7 phases of flight.