Before you practise maneuvers in a simulator, it helps to know why an airplane responds the way it does. This guide covers the core aerodynamics taught in the FAA’s Pilot’s Handbook of Aeronautical Knowledge (PHAK): the four forces, how a wing produces lift, the three axes of motion, and the controls that move the airplane around them. It then ties each control back to the hardware on your desk.
How Does a Plane Fly? The Four Forces
An airplane in flight is acted on by four forces:
- Lift acts upward, perpendicular to the flight path, and is produced mainly by the wings.
- Weight is the pull of gravity, acting downward through the center of gravity.
- Thrust is the forward force from the propeller or jet engine.
- Drag is the rearward resistance of the air.
In steady, unaccelerated flight (constant speed, constant altitude, or a steady climb or descent) these forces are in balance. Change one of them, such as adding power, and the airplane accelerates, climbs, or both until a new balance is reached. Much of learning to fly is learning to manage that balance with pitch and power.
How a Wing Makes Lift
A wing is shaped and angled so that it turns the oncoming air downward. Two complementary ways of describing the result appear in the PHAK:
- Bernoulli’s principle: air flowing over the curved upper surface speeds up and its pressure drops. The higher pressure below the wing pushes it upward.
- Newton’s third law: the wing deflects air downward (downwash), and the equal and opposite reaction pushes the wing up.
Both describe the same physics from different angles. What matters for a pilot is that lift depends on air density, airspeed, wing area, and angle of attack.
Angle of attack and the stall
Angle of attack (AOA) is the angle between the wing’s chord line and the relative wind, meaning the direction the air is coming from. Increasing AOA increases lift, up to a point. Beyond the critical angle of attack, airflow separates from the top of the wing and lift drops sharply. That’s a stall.
A wing can stall at any airspeed and in any attitude if the critical AOA is exceeded. Speed is only an indirect clue. This idea is central to slow flight and stall practice.
The Three Axes of Flight
All airplane movement happens around three axes that pass through the center of gravity:
| Axis | Runs from | Motion around it | Primary control |
|---|---|---|---|
| Longitudinal | Nose to tail | Roll (banking) | Ailerons |
| Lateral | Wingtip to wingtip | Pitch (nose up/down) | Elevator |
| Vertical | Top to bottom | Yaw (nose left/right) | Rudder |
Primary Flight Controls
Primary controls are the ones you use continuously to control the airplane’s attitude and direction.
Ailerons (roll)
Ailerons sit on the outer trailing edge of each wing and move in opposite directions. Turning the yoke or moving the stick left raises the left aileron and lowers the right one. The right wing gains lift, the left wing loses lift, and the airplane rolls left. Banking is what actually turns an airplane: tilting the lift vector gives it a sideways component.
Elevator (pitch)
The elevator is hinged to the horizontal stabilizer at the tail. Pulling back raises the elevator, pushes the tail down, and pitches the nose up. Some aircraft use a stabilator, an all-moving horizontal tail that does the same job. Pitch changes angle of attack, so the elevator is really your angle-of-attack control.
Rudder (yaw)
The rudder is hinged to the vertical stabilizer and moved by the rudder pedals. Pushing the left pedal swings the nose left. The rudder doesn’t turn the airplane on its own the way a car’s steering does. Its main jobs are keeping the airplane coordinated in turns and climbs, controlling direction on the ground, and handling crosswinds, as covered in crosswind landings in a flight sim.
What Is Adverse Yaw?
When you roll into a turn, the aileron that goes down increases lift on its wing, and it increases drag on that wing too. That extra drag pulls the nose briefly toward the opposite direction of the turn. Roll right, and the nose initially yaws left. This is adverse yaw.
Pilots counter it by applying rudder in the direction of the turn as they roll in, which is called coordinating the turn. The inclinometer ball on the turn coordinator shows whether you’ve got it right: keep the ball centered (“step on the ball”). In a simulator, adverse yaw is easy to miss if auto-rudder is switched on, so turn that assist off once you have rudder pedals or a twist-grip stick.
Secondary Flight Controls
Secondary controls change the wing’s lift and drag characteristics or relieve control pressure. You set them occasionally rather than moving them constantly:
- Flaps extend from the inboard trailing edge. They increase lift and drag, which allows slower approach speeds and steeper descents without gaining speed.
- Leading-edge devices (slats and slots) help airflow stay attached at high angles of attack, delaying the stall. They’re common on airliners and some light aircraft.
- Spoilers and speed brakes disrupt airflow over the wing to reduce lift and increase drag. Airliners use them to descend or slow down, and to dump lift after touchdown.
- Trim systems use small tabs or an adjustable stabilizer to hold the controls in a set position without pilot effort. They’re covered in detail in how to use elevator trim.
Primary vs Secondary Controls: The Difference
The simplest way to remember it: primary controls move the airplane around its axes, and secondary controls change how the airplane performs or how hard the primary controls are to hold. You can fly without touching the flaps or trim. You can’t fly without the ailerons, elevator, and rudder.
Power Controls
In a typical piston trainer, three engine controls sit alongside the flight controls:
- Throttle, which sets engine power
- Mixture, which sets the fuel-to-air ratio and is leaned at higher altitudes
- Propeller control, found on airplanes with constant-speed propellers, which sets propeller RPM
Jets and many airliners replace these with thrust levers, often with an autothrottle. The basic idea is the same: pitch and power together set airspeed and vertical path.
How Controls Connect to the Surfaces
- Mechanical systems use cables, pulleys, and push rods. Most light aircraft work this way, and the pilot feels the air loads on the surfaces through the controls.
- Hydraulic or power-assisted systems are used on larger, faster aircraft where the forces would be too heavy for a person.
- Fly-by-wire systems send electronic commands to actuators through flight computers, which can add protections against exceeding safe limits. The Airbus A320 family is a well-known example, covered in our A320 tutorial for MSFS.
Mapping It All to Your Sim Controls
| Real control | Typical sim hardware | Setup tip |
|---|---|---|
| Ailerons | Yoke rotation or stick left/right | Small null zone; start with a linear response |
| Elevator | Yoke push/pull or stick fore/aft | Same as ailerons; avoid heavy curves early on |
| Rudder | Rudder pedals or stick twist | Turn off auto-rudder once you have an axis |
| Toe brakes | Pedal toe axes | Map left and right separately for differential braking |
| Elevator trim | Trim wheel or hat/buttons | Put it somewhere you can reach without looking |
| Flaps | Lever, switch, or buttons | Use “flaps up/down one notch” bindings |
| Throttle, mixture, prop | Throttle quadrant levers | Match the order and colors of the real aircraft if possible |
Most consumer controls use springs to center themselves, so the force you feel doesn’t change with airspeed as it does in a real airplane. That’s normal. Rely on attitude and instruments rather than “feel” in the sim, and expect real controls to feel heavier and to change with speed.
Where to Read More: The PHAK
The FAA’s Pilot’s Handbook of Aeronautical Knowledge is free to download and is the standard reference for this material. Its chapters on the principles and aerodynamics of flight and on flight controls go deeper into stability, load factor, and turning flight. Once these concepts make sense, the next step is learning the instruments that show you what the airplane is doing. See the six pack of flight instruments explained, or return to our learn-to-fly simulator roadmap for the full sequence.