Learn to Fly

The Six Pack of Flight Instruments Explained

What each of the six basic flight instruments shows, which run on pitot-static, vacuum, or electric power, how they fail, and how to practise reading them in a sim.

On this page
  1. What Is the Six Pack?
  2. The Pitot-Static Instruments
  3. The Gyroscopic Instruments
  4. Which Instruments Use Vacuum?
  5. Failures and How They Show Up
  6. Scanning the Six Pack
  7. Six Pack vs Glass Cockpit
  8. Practising With the Six Pack in a Simulator

The “six pack” is the cluster of six core flight instruments found in front of the pilot in most traditional light aircraft. Learning to read them quickly, and to spot when one is lying to you, is one of the most useful things you can practise in a flight simulator. This guide explains each instrument, the system that powers it, how it fails, and how to build a scan.

What Is the Six Pack?

The six basic instruments are usually arranged in two rows of three:

Row Left Center Right
Top Airspeed indicator Attitude indicator Altimeter
Bottom Turn coordinator Heading indicator Vertical speed indicator

The attitude indicator sits top center because it’s the instrument you look at most. The airspeed indicator, attitude indicator, altimeter, and heading indicator form a “T” shape, sometimes called the basic T. The six instruments split naturally into two groups by how they work.

The Pitot-Static Instruments

These three instruments measure air pressure. The pitot tube faces into the airflow and senses ram (total) pressure. The static ports, usually on the side of the fuselage, sense the still-air pressure around the aircraft.

Airspeed indicator

The airspeed indicator compares pitot pressure with static pressure and shows the difference as indicated airspeed, usually in knots. Colored arcs mark important ranges:

  • White arc: flap operating range
  • Green arc: normal operating range
  • Yellow arc: caution range, for smooth air only
  • Red line: never-exceed speed

Exact values differ between aircraft, so always check the specific airplane’s handbook.

Altimeter

The altimeter is an aneroid barometer that converts static pressure into altitude. Because air pressure changes with the weather, the pilot sets the current local pressure in a small window (the Kollsman window), so the altimeter reads altitude above mean sea level. Setting it to standard pressure, 29.92 inHg, gives pressure altitude, which is the basis of flight levels.

Vertical speed indicator

The VSI shows rate of climb or descent in feet per minute. It works through a calibrated leak: static pressure feeds a diaphragm directly and the surrounding case through a small restriction, and the lag between them shows the rate of change. A conventional VSI shows a trend almost immediately but takes several seconds to settle on an accurate rate. An instantaneous VSI (IVSI) adds accelerometers to reduce that lag.

The Gyroscopic Instruments

These instruments use spinning gyroscopes, which resist changes to their orientation. That stability is what lets them show attitude and heading.

Attitude indicator

Also called the artificial horizon, the attitude indicator shows pitch and bank relative to the horizon. A miniature airplane symbol sits against a blue-over-brown background. It’s the master instrument for instrument flying: you set an attitude here and then confirm the result on the other instruments.

Heading indicator

The heading indicator, or directional gyro, shows magnetic heading on a compass card. It’s much easier to read in turns than the magnetic compass, which swings and has acceleration and turning errors. But it drifts over time because of gyroscopic precession and the Earth’s rotation. Pilots realign it with the magnetic compass in straight, unaccelerated flight, commonly about every 15 minutes.

Turn coordinator

The turn coordinator combines two indications:

  • The miniature airplane shows rate of turn. Aligning a wing with the “L” or “R” mark gives a standard-rate turn of 3 degrees per second, a full circle in two minutes.
  • The inclinometer ball shows whether the turn is coordinated. If the ball isn’t centered, add rudder on the side the ball has moved toward. Our guide to flight controls and adverse yaw explains why.

Some older aircraft have a turn-and-slip indicator instead, which shows rate of turn but doesn’t respond to roll rate the way a turn coordinator does.

Which Instruments Use Vacuum?

In many traditional light aircraft, the attitude indicator and heading indicator are vacuum-driven. An engine-driven vacuum pump draws air through the instruments to spin their gyros. The turn coordinator is usually electric. Splitting power sources this way means a single vacuum pump failure doesn’t take out every gyro instrument. Some aircraft use electric gyros throughout or have backups, so check the panel of the specific airplane. In most modern glass-cockpit aircraft, solid-state sensors have replaced vacuum gyros.

Failures and How They Show Up

Failure Instruments affected Typical symptom
Pitot tube blocked (drain hole open) Airspeed Airspeed drops toward zero
Pitot tube and drain blocked Airspeed Acts like an altimeter: reads higher in a climb, lower in a descent
Static ports blocked Airspeed, altimeter, VSI Altimeter freezes, VSI reads zero, airspeed becomes unreliable
Vacuum pump failure Attitude and heading indicators Slow, gradual drift or tumbling, which can be hard to notice
Electrical failure Turn coordinator (if electric) Off flag or frozen indication

Many aircraft have an alternate static source for static blockages. Using it usually makes the altimeter and airspeed read slightly high, because cabin pressure tends to be a little lower than outside.

The most dangerous failures are the slow ones. A vacuum failure can make the attitude indicator lean gently while everything else shows a turn. That’s why pilots cross-check.

Scanning the Six Pack

A common method is the radial scan: the attitude indicator is the hub. Glance at it, then out to one other instrument, then back to the attitude indicator, then to another, and so on. For example, when holding altitude:

  1. Attitude indicator: level pitch, wings level
  2. Altimeter: holding?
  3. Back to attitude: small correction if needed
  4. Heading indicator: on heading?
  5. Back to attitude
  6. Airspeed and VSI as needed

Don’t stare at one instrument (fixation), skip instruments (omission), or put too much weight on one reading (emphasis). These are the classic scan errors described in FAA instrument training material.

Six Pack vs Glass Cockpit

Glass cockpits such as the Garmin G1000 put the same information on a primary flight display:

  • airspeed as a tape on the left
  • altitude as a tape on the right, with vertical speed beside it
  • attitude in the center
  • heading on a compass rose (HSI) below
  • a slip/skid indicator under the bank pointer

The principles are identical, just presented differently. If you learn the six pack first, the glass layout makes sense quickly. See Garmin G1000 basics in Microsoft Flight Simulator.

Practising With the Six Pack in a Simulator

  • Pick a steam-gauge aircraft. Many sims include a classic Cessna 172 or similar with round dials.
  • Fly by instruments alone. Set the weather to low clouds, or limit your view to the panel, and practise straight-and-level flight, climbs, descents, and standard-rate turns.
  • Trim properly. A trimmed airplane makes the scan far easier; see how to use elevator trim.
  • Use failures. X-Plane and other sims let you fail the vacuum system or block the pitot-static system. Practise recognising the failure, covering the bad instruments, and flying partial panel.
  • Navigate with them. Once the scan feels natural, add radio navigation with VOR tracking.

For where this fits in an overall training plan, see our learning to fly with a flight simulator roadmap.

The complete guide to learn to fly

Learning to Fly with a Flight Simulator
Read the guide

Keep exploring

Guides from other topics

All topics →