The quick answer
To start the default Boeing 747-8 from cold and dark in Microsoft Flight Simulator:
- Switch on the battery and set standby power to AUTO.
- Start the APU and bring its generators online.
- Set the three IRS switches to NAV.
- Turn on the fuel pumps and beacon, and make sure APU bleed air is available.
- Start each engine by pulling its start switch and moving its fuel control switch to RUN.
- Once all four are running, switch the APU off and the air-conditioning packs on.
If you just want to fly, press Ctrl+E, the default auto-start shortcut, or spawn at the gate with engines running.
The detailed steps below describe the general sequence. Exact switch behaviour can differ between MSFS 2020 and MSFS 2024 and between sim updates. For definitive procedures, use Working Title’s official 747-8 instructions and reference document, linked from the MSFS aircraft manuals page.
The fastest way: autostart or spawn ready
- Auto-start (Ctrl+E): with the default key bindings, this starts the engines automatically. It’s handy when you’re learning other parts of the flight first.
- Spawn ready to go: choosing a runway or a gate with engines running, depending on your version’s options, skips startup entirely.
- Checklist assistance: the in-sim checklists can highlight the next switch and, if enabled, set it for you.
Cold and dark is worth learning eventually. It’s one of the most satisfying parts of flying a heavy jet.
Before you begin
- Park at a gate or stand with the parking brake set.
- Have your flight plan ready, since you’ll enter it into the FMC while the IRS aligns.
- Keep the overhead panel in view. Most of the startup happens there.
- Consider loading fuel and payload first, through the EFB or weight-and-balance screen.
Step 1: Power up
- Battery switch: ON. Lift the guard if there is one.
- Standby power: AUTO.
- External power: if a ground power unit is available at your stand, you can connect it to save APU fuel. Otherwise, go straight to the APU.
The displays should start to come alive.
Step 2: Start the APU
- Turn the APU selector to START, then release it. It springs back to ON.
- Wait for the APU to spool up and for the APU GEN switches to show AVAIL.
- Press the APU GEN 1 and 2 switches to put APU power on the electrical buses. If external power was connected, it will be replaced.
The APU now provides electrical power and bleed air for engine start.
Step 3: Align the IRS and set up the FMC
- Set all three IRS selectors to NAV.
- Alignment takes a few minutes. Don’t move the aircraft while it completes. Pushback can wait.
- While it aligns, program the FMC: position, route, departure, performance and takeoff speeds.
Some simmers use the realism settings to speed up alignment. It’s fine either way.
Step 4: Fuel, bleed air and pre-start
- Fuel pumps: turn on the main tank pumps, and the override or centre pumps if you have centre-tank fuel.
- Lights: navigation and logo lights as required, then the beacon ON before engine start. That’s the signal to ground crew that engines are about to start.
- Bleed air: make sure the APU bleed is on and the duct isolation valves are open, so starting air can reach every engine.
- Packs: many procedures switch the air-conditioning packs off for engine start, so more bleed air goes to the starters.
- Doors closed and pushback complete, if you need one.
Step 5: Start the four engines
Engines are commonly started one at a time, often in the order 4, 3, 2, 1. For each engine:
- Pull the start switch for that engine.
- Move the engine’s fuel control switch to RUN. On the 747-8, the autostart system manages fuel and ignition timing, so check your version’s reference guide for exactly when to do this. Older 747 procedures waited for a set N2 value before introducing fuel.
- Watch the EICAS: N2 rises, then fuel flow, EGT and N1. Wait for the engine to stabilise at idle before starting the next.
Repeat for each engine.
Step 6: After start
- APU bleed: off, once engines are supplying bleed air.
- APU: off, once engine generators are online.
- Packs: back on.
- Hydraulic demand pumps: AUTO.
- Flaps: set for takeoff according to your FMC performance data.
- Run the after-start and before-taxi checklists.
You’re ready to taxi. Remember that the 747’s main gear sits far behind you, so take turns wide and slow. Our guide to flying the 747 has more handling tips.
Troubleshooting: why won’t my 747 start?
- No bleed air: the APU isn’t running, APU bleed is off, or the isolation valves are closed. The starters need air.
- Packs still on: they can take too much bleed air during start in some versions.
- Fuel problems: pumps off, fuel control switch still at CUTOFF, or no fuel loaded.
- APU not ready: wait for APU GEN to show AVAIL before you continue.
- Add-on or mod conflicts: a modified 747 package, such as an old mod after a sim update, can break the startup logic. Test with mods disabled.
- Version differences: procedures written for MSFS 2020 may not match MSFS 2024 exactly. Check that the guide you’re following matches your version.
For the bigger picture of what’s in the hangar beyond the 747, see our flight sim aircraft and add-ons hub.